background image

 

EWLP012~065KAW1N

 

Condenserless water-cooled water chillers

 

4PW30043-1

 

Operation manual

 

2

 

Electrical specifications

 

(1)

 

A

 

D

 

ESCRIPTION

 

The EWLP condenserless water-cooled water chillers are available in 7 standard sizes.

 

Figure:  

 

Main components 

 

(1) Refer to the engineering data book for the complete list of specifications.

 

Model EWLP

 

012

020

026

030

Power supply

 

• Phase

3N~

• Frequency

 

(Hz)

 

50

• Voltage

 

(V)

 

400

• Voltage tolerance

 

(%)

 

±10

• Recommended fuses

 

(aM)

 

3x 16

3x 20

3x 25

3x 32

 

Compressor

 

• Phase

3~

• Frequency

 

(Hz)

 

50

• Voltage

 

(V)

 

400

• Nominal running current (A)

7.4

11.6

14.7

16.8

 

Control

 

• Phase

1~

• Frequency

 

(Hz)

 

50

• Voltage

 

(V)

 

230

• Recommended fuses

 

(aM)

 

factory installed

 

Model EWLP

 

040

055

065

Power supply

 

• Phase

3N~

• Frequency

 

(Hz)

 

50

• Voltage

 

(V)

 

400

• Voltage tolerance

 

(%)

 

±10

• Recommended fuses

 

(aM)

 

3x 40

3x 50

3x 50

 

Compressor

 

• Phase

3~

• Frequency

 

(Hz)

 

50

• Voltage

 

(V)

 

400

• Nominal running current (A)

11.6

14.7

16.8

 

Control

 

• Phase

1~

• Frequency

 

(Hz)

 

50

• Voltage

 

(V)

 

230

• Recommended fuses

 

(aM)

 

factory installed

13

14

15

16

17

500

500

500

5

10

2

3

1

4

10

11

11

9

2

3

4

3

1

1

7

5

9

8

6

6

18

18

12

12

7
8

500

500

500

500

500

EWLP012~030KAW1N

EWLP040~065KAW1N

 

1

 

Compressor

 

2

 

Evaporator

 

3

 

Accumulator

 

4

 

Switchbox

 

5

 

Chilled water in

 

6

 

Chilled water out

 

7

 

Discharge stop valve

 

8

 

Liquid stop valve

 

9

 

Evaporator entering water temperature sensor

 

10

 

Freeze up sensor

 

11

 

Digital display controller

 

12

 

Power supply intake

 

13

 

Ball valve (field installed)

 

14

 

Water filter (field installed)

 

15

 

Air purge valve (field installed)

 

16

 

T-joint for air purge (field installed)

 

17

 

Flow switch (with T-joint) (field installed)

 

18

 

Main switch

Required space around the unit for service

Содержание Hydrocube EWLP012KAW1N

















Отзывы: