background image

Installation and operation manual

2

125A8V1BF

VRV IV System indoor unit

4P405267-1C – 2021.04

1. About the documentation

1.1.

About this document

This document is an installation manual. It is intended for authorized

installers  of  this  product.  It  describes  the  procedures  for  installing,

commissioning  and  maintaining  the  unit,  and  it  will  provide  help  if

problems occur. Carefully read the relevant parts of the manual.
This  document  is  also  an  operation  manual.  It  is  intended  for  the

installer and the user of this product. It describes how to operate and

maintain the unit, and it will provide help if problems occur. Carefully

read the relevant parts of the manual.

1.2.

Scope of the manual

This manual does NOT include the selection procedure and the water

system design procedure. Only some precautions and tips and tricks

about the design of the water circuit are given in a separate chapter

of this manual.
Once  the  selection  is  done  and  the  water  system is designed, this

manual  describes  the  procedures  for  handling,  installing  and

connecting the HXY080/125 units. This manual has been prepared to

ensure adequate maintenance of the unit, and it will provide help if

problems occur.

1.3.

Documentation set

This  document  is  part  of  a  documentation  set.  The  complete  set

consists of:

Latest revisions of the supplied documentation may be available on

the regional Daikin website or via your dealer.

2. General safety precautions

2.1.

For the user

If you are not sure how to operate the unit, contact your installer.

The  appliance  is  not  intended  for  use  by  persons,  including

children, with reduced physical, sensory or mental capabilities,

or  lack  of  experience  and  knowledge,  unless  they  have  been

given supervision or instruction concerning use of the appliance

by  a  person  responsible  for  their  safety.  Children  must  be

supervised to ensure that they do not play with the product.

Units are marked with the following symbol:

This means  that  electrical  and electronic  products  may  not  be

mixed with unsorted household waste. Do NOT try to dismantle

the system yourself: the dismantling of the system, treatment of

the  refrigerant,  of  oil  and  of  other  parts  must  be  done  by  an

authorized installer and must comply with applicable legislation.

Units  must  be  treated  at  a  specialized  treatment  facility  for

reuse,  recycling  and  recovery.  By  ensuring  this  product  is

disposed of correctly, you will help to prevent potential negative

consequences for the environment and human health. For more

information, contact your installer or local authority.

2.2.

For the installer

2.2.1. General

If  you  are  not  sure  how  to  install  or  operate  the  unit,  contact  your

dealer.

In accordance with the applicable legislation, it might be necessary to

provide a logbook with the product containing at least: information on

maintenance, repair work, results of tests, stand-by periods,…
Also,  at  least,  following  information  must  be  provided  at  an

accessible place at the product:

Instructions  for  shutting  down  the  system  in  case  of  an

emergency.

Name and address of fire department, police and hospital.

Name,  address  and  day  and  night  telephone  numbers  for

obtaining service.

In Europe, EN378 provides the necessary guidance for this logbook.

Document

Contains…

Format

Indoor unit 

installation/operation 

manual

Installation and 

operator instructions

Indoor unit 

installation/operation 

manual

Outdoor unit installation 

manual

See info delivered with 

outdoor unit.

CAUTION

Do NOT rinse the unit. This may cause electric shocks or

fire.

NOTICE

Do NOT place any objects or equipment on top of the

unit.

Do NOT sit, climb or stand on the unit.

NOTICE

Improper  installation  or  attachment  of  equipment  or

accessories  could  result  in  electric  shock,  short-circuit,

leaks,  fire  or  other  damage  to  the  equipment.  Only  use

accessories, optional equipment and spare parts made or

approved by Daikin.

WARNING

Make  sure  installation,  testing  and  applied  materials

comply  with  applicable  legislation  (on  top  of  the

instructions described in the Daikin documentation).

CAUTION

Wear adequate personal protective equipment (protective

gloves,  safety  glasses,…)  when  installing,  maintaining  or

servicing the system.

DANGER: RISK OF BURNING

Do NOT touch the refrigerant piping, water piping or

internal parts during and immediately after operation.

It could be too hot or too cold. Give it time to return to

normal  temperature.  If  you  must  touch  it,  wear

protective gloves.

Do NOT touch any accidental leaking refrigerant.

Содержание HXY080A8V1BF

















































Отзывы: