background image

2

 | 

General safety precautions

Installer reference guide

13

FTXF20~4 ATXF20~42C5V1B
Daikin room air conditioner
4P519439-9J – 2021.06

If

Then

A siphon tube is present

(i.e., the cylinder is marked with "Liquid
filling siphon attached")

Charge with the cylinder upright.

A siphon tube is NOT present

Charge with the cylinder upside down.

Open refrigerant cylinders slowly.

Charge the refrigerant in liquid form. Adding it in gas form may prevent normal
operation.

CAUTION

When the refrigerant charging procedure is done or when pausing, close the valve of
the refrigerant tank immediately. If the valve is NOT closed immediately, remaining
pressure  might  charge  additional  refrigerant. 

Possible  consequence: 

Incorrect

refrigerant amount.

2.2.4 Electrical

DANGER: RISK OF ELECTROCUTION

Turn  OFF  all  power  supply  before  removing  the  switch  box  cover,  connecting
electrical wiring or touching electrical parts.

Disconnect the power supply for more than 10 minutes, and measure the voltage
at  the  terminals  of  main  circuit  capacitors  or  electrical  components  before
servicing. The voltage MUST be less than 50 V DC before you can touch electrical
components. For the location of the terminals, see the wiring diagram.

Do NOT touch electrical components with wet hands.

Do NOT leave the unit unattended when the service cover is removed.

WARNING

If  NOT  factory  installed,  a  main  switch  or  other  means  for  disconnection,  having  a
contact  separation  in  all  poles  providing  full  disconnection  under  overvoltage
category III condition, MUST be installed in the fixed wiring.

Содержание FTXF-C

























































Отзывы: