Daikin FFQ09Q2VJUFFQ12Q2VJUFFQ15Q2VJUFFQ18Q2VJURX09QMVJURX12QMVJURX15QMVJURX18QMVJU Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 146

Daikin FFQ09Q2VJUFFQ12Q2VJUFFQ15Q2VJUFFQ18Q2VJURX09QMVJURX12QMVJURX15QMVJURX18QMVJU Скачать руководство пользователя страница 54

Control Specification

SiUS091628EA

43

Functions and Control

2.12 Malfunctions

2.12.1 Sensor Malfunction Detection

Sensor malfunction can be detected in the following thermistor:
1. Outdoor heat exchanger thermistor
2. Discharge pipe thermistor
3. Radiation fin thermistor
4. Outdoor temperature thermistor

2.12.2 Detection of Overcurrent and Overload

Outline

An excessive output current is detected and the OL temperature is observed to protect the
compressor.

Details

If the OL (compressor head) temperature exceeds 130°C (266°F), the system shuts down the
compressor.

If the inverter current exceeds 12.0 ~ 12.5 A, the system shuts down the compressor.
The upper limit of the current decreases when the outdoor temperature exceeds a certain level.

«
...
52
53
54
55
56
...
»

Содержание FFQ09Q2VJUFFQ12Q2VJUFFQ15Q2VJUFFQ18Q2VJURX09QMVJURX12QMVJURX15QMVJURX18QMVJU



















































































































































Отзывы:

Нет отзывов