background image

10

 | 

Maintenance and service

Installer and user reference guide

36

FAA71+100BUV1B

Split system air conditioner

4P654517-1 – 2021.03

3

Clean the front panel. Wipe it with a soft cloth soaked in water by using only
neutral detergent.

4

Wipe panel with a dry soft cloth and let it dry up in the shade.

5

Attach the front panel. Align the hooks of the front panel with the slots and
push them all the way in.

6

Close the front panel slowly.

10.2.3 To clean the air filter

NOTICE

Do  NOT  use  water  of  50°C  or  higher. 

Possible  consequence: 

Discoloration  and

deformation.

When to clean the air filter

:

Rule  of  thumb:  Clean  every  6  months.  If  the  air  in  the  room  is  extremely
contaminated, increase the cleaning frequency.

Depending  on  the  settings,  the  user  interface  can  display  the 

"Time  to  clean

filter" 

notification. Clean the air filter when the notification is displayed.

If  the  dirt  becomes  impossible  to  clean,  change  the  air  filter  (=  optional
equipment).

How to clean the air filter

:

1

Open  the  front  panel.

  Hold  the  front  panel  by  the  panel  tabs  on  both  sides

and open until the panel stops.

a

a

Panel tab

2

Remove  the  air  filter.

  Push  up  the  tab  in  the  center  of  the  air  filter  slightly

then pull the air filter out in a downward direction.

Содержание FAA71BUV1B

























































































Отзывы: