Daikin EWWQ090G Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 58

Daikin EWWQ090G Скачать руководство пользователя страница 29

EWWQ090G ÷  EWWQ720L - R410a - Water-cooled scroll chillers
EWLQ090G   ÷ EWLQ720L   - R410a - Condenser less
EWHQ100G  ÷ EWHQ400G  - R410a - Heat pump scroll chillers

Water cooled scroll chillers & heat pump

Operation

Manual

EWWQ - EWLQ - EWHQ

Water cooled scroll chiller &heat
pump
D-EOMWC01203-15EN

Operation Manual

29

Heat/Cool w/Glycol
Heat/Ice w/Glycol
Pursuit
Test

4.7 Timers

This page indicates the remaining cycle timers for each compressor. When the cycle timers are
active any new start of a compressor is inhibited.

Setpoint/Sub-Menu

Default

Range

Description

Comp 1=

0s

Comp 2=

0s

Comp 3=

0s

Comp 4=

0s

Clear Cycle Tmrs

Off

Off,On

Clear Cycle Timers

Stg Up Dly Rem=

Stg Dn Dly Rem=

Clr Stg Delays=

Off

Off,On

Clear Stages Delays

Ice Cycle Dly Rem

Clear Ice Dly=

Off

Off,On

Cleat Ice Delay

4.8 Alarms

This link jumps to the Alarm page. Each of the items represents a link to a page with different
information. The information shown depends on the abnormal operating condition that caused the
activation of unit, circuit or compressor safeties. A detailed description of the alarms and how to
handle will be discussed in the section Troubleshooting this chiller.

Setpoint/Sub-Menu

Default

Description

Alarm Active



List of the active alarms

Alarm Log



History of all the alarms and acknowledges

Event Log



List of the events

Alarm Snapshot



List of alarm snapshots with all the relevant data recorded at time the alarm occurred.

4.9 Commission Unit

Setpoint/Sub-Menu

Default

Range

Description

Configure Unit



See section 4.9.1

Alarm Limits



See Section 4.9.2

Calibrate Unit Sensors



See section 4.9.3

Calibrate Circuit Sensors



See section 4.9.4

Unit Manual Control



See section 4.9.5

Circuit 1 Manual Control



See section 4.9.6

Circuit 2 Manual Contorl



Scheduled Maintenance



See section 4.9.7

4.9.1 Configure Unit

This page resumes all the specific settings for this unit like unit type, number of circuits, type of
condensing control, etc.. Part of these settings cannot be adjusted and are supposed to be set
during the manufacturing or commissioning of this unit. The modification of each parameter in this
menu requires that the unit switch is set to 0.

Setpoint/Sub-

Menu

Default

Range

Description

Apply Changes=

No

No, Yes

Type yes after changes

Unit Type=

EWWD

EWWD, EWLD

Select the unit type, chiller (EWWD) or condenser less
(EWLD)

Number Of Cir=

1

1,2

Number of circuit of the chiller

Inversion Type

No

No, Water, Gas

Type of inversion in heat pump mode.

Cond Ctrl Var=

No

No, Pressure, Cond In, Cond Out

Enabling of the condensing control

Cond Ctrl Dev=

None

None, Valve, VFD

Select device type used for condensing control

«
...
27
28
29
30
31
...
»

Содержание EWWQ090G



























































Отзывы:

Нет отзывов