Daikin EWWQ090G Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 58

Daikin EWWQ090G Скачать руководство пользователя страница 18

EWWQ090G ÷  EWWQ720L - R410a - Water-cooled scroll chillers
EWLQ090G   ÷ EWLQ720L   - R410a - Condenser less
EWHQ100G  ÷ EWHQ400G  - R410a - Heat pump scroll chillers

Water cooled scroll chillers & heat pump

Operation

Manual

Operation Manual

18

EWWQ - EWLQ - EWHQ

Water colled scroll chiller &heat pump
D-EOMWC01203-15EN

Solid Yellow

Communication running but parameter from the application wrong or missing, or uncorrect factory calibration

Solid Red

Communication down (*)

Communication modules

BSP LED (same for all modules)

BSP LED

Mode

Solid Green

BPS running, communication with controller

Solid Yellow

BSP running, no communication with controller (*)

Solid Red

Hardware Error (*)

Flashing Red

BSP Error (*)

Flashing Red/Green

Application/BSP update

(*) Contact Service.

LON module BUS LED

BUS LED

Mode

Solid Green

Ready for Communication. (All Parameter loaded, Neuron configured). Doesn't indicate a communication
with other devices.

Solid Yellow

Startup

Solid Red

No Communication to Neuron (internal error, could be solved by downloading a new LON application)

Flashing
Yellow

Communication not possible to the Neuron. The Neuron must be configured and set online over the LON
Tool.

Bacnet MSTP BUS LED

BUS LED

Mode

Solid Green

Ready for Communication. The BACnet Server is started. It doesn't indicate a active communication

Solid Yellow

Startup

Solid Red

BACnet Server down. Automatically a restart after 3 seconds are initiated.

Bacnet IP BUS LED

BUS LED

Mode

Solid Green

Ready for Communication. The BACnet Server is started. It doesn't indicate a active communication

Solid Yellow

Startup. The LED stays yellow until the module receives a IP Address, therefore a link must be established.

Solid Red

BACnet Server down. Automatic restart after 3 seconds is initiated.

Modbus BUS LED

BUS LED

Mode

Solid
Green

All Communication running

Solid
Yellow

Startup, or one configured channel not communicating to the Master

Solid Red

All configured Communications down. Means no communication to the Master. The timeout can be configured.
In case that the timeout is zero the timeout is disabled.

«
...
16
17
18
19
20
...
»

Содержание EWWQ090G



























































Отзывы:

Нет отзывов