Daikin EWWQ090G Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 58

Daikin EWWQ090G Скачать руководство пользователя страница 13

EWWQ090G ÷  EWWQ720L - R410a - Water-cooled scroll chillers
EWLQ090G   ÷ EWLQ720L   - R410a - Condenser less
EWHQ100G  ÷ EWHQ400G  - R410a - Heat pump scroll chillers

Water cooled scroll chillers & heat pump

Operation

Manual

EWWQ - EWLQ - EWHQ

Water cooled scroll chiller &heat
pump
D-EOMWC01203-15EN

Operation Manual

13

CAUTION: Maintain the correct polarity when connecting the power supply to the boards,
otherwise the peripheral bus communication will not operate and the boards may be
damaged.

2.5 Communication Modules

Any  of  the  following  modules  can  be  connected  directly  to  the  left  side  of  the  main  controller  to
allow a BAS or other remote interface to function.  Up to three can be connected to the controller at
a  time.    The  controller  should  automatically  detect  and  configure  itself  for  new  modules  after
booting up.  Removing modules from the unit will require manually changing of the configuration.

Module

Siemens Part Number

Usage

BacNet/IP

POL908.00/MCQ

Optional

Lon

POL906.00/MCQ

Optional

Modbus

POL902.00/MCQ

Optional

BACnet/MSTP

POL904.00/MCQ

Optional

«
...
11
12
13
14
15
...
»

Содержание EWWQ090G



























































Отзывы:

Нет отзывов