background image

D-EIMHP01501-22_00EN

 

12/20 

 

13. 

OPERATOR’S REPONSIBILITIES 

It  is  essential  that  the  operator  is  appropriately  trained  and  becomes  familiar  with  the  system  before  operating  the  unit.  In 
addition  to  reading  this  manual,  the  operator  must  study  the  microprocessor  operating  manual  and  the  wiring  diagram  to 
understand start-up sequence, operation, shutdown sequence and operation of all the safety devices. 

During the unit initial start-up phase, a technician authorized by the manufacturer is available to answer any questions and 
to give instructions as to the correct operating procedures. 

The operator must keep a record of operating data for every 

R41

 installed unit. Another registration must also be kept for 

all the periodic maintenance and assistance activities. 

If the operator notes abnormal or unusual operating conditions, he is advised to consult the technical service authorized 
by the manufacturer. 

 

 

 

WARNING

 

If  the  unit  is  switched  off,  the  compressor  oil  heater  cannot  be  used.  Once  the  unit  is 

reconnected to the mains, leave the compressor oil heater charged for at least 6 hours before restarting 
the unit. 

Failure to observe this rule may cause damage to the compressors due to excessive accumulation of 
liquid inside them.

 

 

This unit represents a substantial investment and deserves the attention and care to keep this equipment in good working 
order. 

However, during operation and maintenance it is essential to observe the following instructions: 

 

Do not allow unauthorized and / or unqualified personnel to access the unit. 

 

It is forbidden to access the electrical components without having opened the unit main switch and switched off the 
power supply. 

 

It  is  forbidden  to  access  the  electrical  components  without  using  an  insulating  platform.  Do  not  access  the  electrical 
components if water and/or moisture are present. 

 

Verify that all operations on the refrigerant circuit and on the components under pressure are carried out exclusively by 
qualified personnel. 

 

The replacement of the compressors must be carried out exclusively by qualified personnel. 

 

Sharp edges and the surface of the condenser section could cause injury. Avoid direct contact and use adequate 
protection device. 

 

Do not introduce solid objects into the water pipes while the unit is connected to the system. 

 

It is absolutely forbidden to remove all protections of moving parts. 

In case of sudden stop of the unit, follow the instructions on the Control Panel Operating Manual which  is part of the on-
board documentation delivered to the end user. 

It is strongly recommended to perform installation and maintenance with other people. 

 

WARNING

 

Avoid installing the unit in areas that could be dangerous during maintenance operations, such 

as platforms without parapets or railings or areas not complying with the clearance requirements around the 
unit.

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание EWWQ-KC





















Отзывы: