EWYT~CZ / EWAT~CZ
DEIMHP0140521_00EN
7
2. reCeiPt of tHe unit
Inspect the unit immediately after delivery. Make sure that the
machine is intact in all its parts and that there are no deformations due
to impacts. All components described in the delivery note must be
inspected and checked.
Should any damage occur upon receipt of the machine, do not
remove the damaged material and immediately make a written
complaint to the transport company, requesting the inspection of the
unit; do not repair until inspection by the transport company
representative is carried out.
Immediately report the damage to the manufacturer representative, a
set of photographs is helpful in recognizing responsibility. The
restitution of the machinery is intended as ex-factory Daikin Applied
Europe S.p.A..
Daikin Applied Europe S.p.A. declines all responsibility for any
damage that the machinery may suffer during transport to the
destination.
Use extreme caution when handling the unit to prevent damage to
components. Before installing the unit, check that the model and
power supply voltage shown on the nameplate are correct.
Responsibility for any damage after acceptance of the unit cannot be
attributed to the manufacturer.
3. storage
If it is necessary to store the unit before installation, it is necessary to
observe some precautions:
■
do not remove the protective plastic;
■
protect the unit from dust, bad weather and any rodents;
■
do not expose the unit to direct sunlight;
■
do not use heat sources and / or open flames near the machine.
Although the unit is covered with a heatshrink plastic sheet, it is not
intended for longterm storage and must be removed and replaced by
tarpaulins or the like, more suitable for a longer period.
Environmental conditions must be within the following limits:
■
Minimum ambient temperature:
20 °C
■
Maximum ambient temperature: +48 °C
■
Maximum R.H.:
95% not condensing
Storage at a temperature below the minimum or over the maximum
values can cause damage to the components. Storage in a humid
atmosphere may damage electrical components.
4. MeCHaniCaL instaLLation
4.1. Safety
Before installation and commissioning of the machinery, the people
involved in this activity must have acquired the information necessary
to perform these tasks, applying all the information gathered in this
manual. In particular:
■
the unit must be firmly anchored to the ground when it must not
be moved;
■
the unit can only be lifted using the lifting points indicated by la-
bels fixed to its base;
■
always protect operating personnel with personal protective
equipment appropriate to the activities to be performed. The in-
dividual devices commonly used are: helmet, glasses, gloves,
headphones, safety shoes. Further personal and collective pro-
tection devices must be adopted after having carried out an ade-
quate analysis of the specific risks in the relevant area, according
to the activities to be carried out.
4.2. Handling and lifting
Avoid bumping and/or jolting during loading/unloading unit from the
truck and moving it. Do not push or pull the unit from any part other
than the base frame. Secure the unit inside the truck to prevent it from
moving and causing damages. Do not allow any part of the unit to fall
during transportation or loading/unloading.
Lifting instructions:
Equipment, ropes, lifting accessories and handling procedures must
comply with local regulations and current legislation.
When lifting the machine, use only the holes in the frame identified in
the figure. Use lifting hooks with closing device exclusively. The hooks
must be safely fastened before performing the handling.
The ropes and hooks used must have an appropriate capacity for the
load. Refer to the plate on the unit for the weight of the specific
machine.
Lifting ropes must have the minimum length shown in the diagram. All
units of the series are supplied with lifting points indicated by labels.
Only these points may be used for lifting the unit, as shown in the
following figures.
The installer has the responsibility to ensure the selection and correct
use of the lifting equipment.
Alternatively, the machine may be moved with a forklift, as shown.
When lifting the machine, make sure it is levelled properly so it will not
overturn.
Содержание EWAT016CZN-A1
Страница 2: ......
Страница 28: ...Notes...
