Daikin EBLA04E V Series Скачать руководство пользователя страница 87

Страница: 87 / 324

Troubleshooting

Service manual

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

Root cause category: component – electrical

Possible failure

Root cause

Check

Repair

Expansion valve incorrect
control - superheat too
low.

▪

Faulty

suction

thermistor,

▪

Faulty expansion valve
control.

▪

Check

suction

thermistor,

▪

Check

the

expansion

valve.

▪

Replace thermistor when
required,

▪

Replace expansion valve
when required.

3.4.8 Symptom: Abnormal presence of ice

Possible failure

Root cause

Check

Repair

General ice build-up.

—

Outdoor unit installation
MUST be protected from
weather (wind, snow, ...).

See installer reference
guide for correct
installation.

Ice build-up on the
outdoor unit.

▪

Clogged drain holes,

▪

Snow on the outdoor
unit,

▪

Ice building up on the
casing.

Ice is NOT in direct contact
with fins.

▪

Unclog  drain  holes  or
remove  any  scraps  that
can  be  used  for  ice  to
build up,

▪

Remove ice.

Defrost operation
malfunction.

NOT enough defrost
power: shortage of
refrigerant.

▪

Check refrigerant charge,

▪

Check for leaks.

▪

Replace refrigerant,

▪

Fix leaks.

Ice build-up at entry spot
of refrigerant.

Refrigerant shortage.

▪

Check refrigerant charge,

▪

Check for leaks.

▪

Replace refrigerant,

▪

Fix leaks.

Partial ice up of coil.

Partial refrigerant
blockage.

Check refrigerant circuit.

Replace part where
blockage occurs.

Dirty coil.

Check if coil is dirty.

Clean coil.

Bad weather conditions.

Unit is NOT powerful
enough to defrost due to
too strong wind, snow, ...

Outdoor unit installation
MUST be protected from
weather (wind, snow, ...).

See installer reference
guide for correct
installation.

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 87 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: