Daikin EBLA04E V Series Скачать руководство пользователя

Страница: 237 / 324

Components

Service manual

237

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

To install the user interface

See relevant manual of the user interface (remote controller) for the correct
procedure.

Is the problem solved?

Action

Yes

No further actions required.

Return to the troubleshooting of the
specific error and continue with the
next procedure.

To adjust the settings

See the relevant documentation (installer reference guide, remote controller
manual, …) to adjust the specific setting.

Is the problem solved?

Action

Yes

No further actions required.

Return to the troubleshooting of the
specific error and continue with the
next procedure.

To install the software

Install the software using the Updater Tool. See the Business Portal (

http://

www.mydaikin.eu

) for more information about the Updater Tool.

Is the problem solved?

Action

Yes

No further actions required.

Return to the troubleshooting of the
specific error and continue with the
next procedure.

4.21 Water flow sensor

4.21.1 Checking procedures

To perform an electrical check of the water flow sensor

Prerequisite:

Stop the unit operation via the user interface.

Prerequisite:

Turn OFF the respective circuit breaker.

Prerequisite:

Remove the required plate work, see

"4.16 Plate work"

[

202].

Turn ON the power of the unit.

Activate

Installer

on the user interface. See the installer reference guide

for the correct procedure.

Go to

Actuator test run

via the user interface.

Activate the

Pump

Select

Flow rate

Result:

The displayed flow rate MUST be 5~60 l/min.

Measure the water flow with a calibrated external flow meter.

Measure the frequency on connector X34A between pins 2‑3 (= flow sensor
output signal) on the hydro PCB.

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Похожие инструкции для EBLA04E V Series

Бренды по названию

Популярные бренды

Daikin EBLA04E V Series, Руководство по обслуживанию

Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Похожие инструкции для EBLA04E V Series

Бренды по названию

Популярные бренды