Daikin DRG0361DL00001S Скачать руководство пользователя страница 47

Страница: 47 / 113

SERVICING

L1 - L2 = 240V

L1 - L3 = 227V

L2 - L3 = 238V

Rotate all 3 incoming

legs as shown.

L1 - L2 = 227V

L1 - L3 = 238V

L2 - L3 = 240V

By the voltage readings we see that the imbalance rotated

or traveled with the switching of the incoming legs.

Therefore the imbalance lies within the incoming power

supply.

If the imbalance had not changed then the problem would

lie within the equipment. Check for current leakage,

shorted motors, etc.

S-2 Checking Wiring

HIGH VOLTAGE!

Disconnect ALL power before servicing

or installing this unit. Multiple power

sources may be present. Failure to do so

may cause property damage, personal injury

or death.

1. Check wiring visually for signs of overheating,

damaged insulation and loose connections.

2. Use an ohmmeter to check continuity of any

suspected open wires.

3. If any wires must be replaced, replace with

comparable gauge and insulation thickness.

S-3 Checking Thermostat, Wiring, And Anticipator

THERMOSTAT WIRE SIZING CHART

LENGTH OF RUN

MIN. COPPER WIRE

GAUGE (AWG)

25 feet

50 feet

75 feet

100 feet

125 feet

150 feet

S-3A Thermostat and Wiring

WARNING

Line Voltage now present.

With power ON, thermostat calling for cooling

1. Use a voltmeter to check for 24 volts at thermostat

wires C and Y in the unit control panel.

2. No voltage indicates trouble in the thermostat or

wiring.

3. Check the continuity of the thermostat and wiring.

Repair or replace as necessary.

Indoor Blower Motor

With power ON:

WARNING

Line Voltage now present.

1. Set fan selector switch at thermostat to “ON”

position.

2. With voltmeter, check for 24 volts at wires C and G.

3. No voltage indicates the trouble is in the thermostat

or wiring.

4. Check the continuity of the thermostat and wiring.

Repair or replace as necessary.

S-3B Cooling Anticipator

The cooling anticipator is a small heater (resistor) in the

thermostat. During the “off” cycle, it heats the bimetal

element helping the thermostat call for the next cooling

cycle. This prevents the room temperature from rising

too high before the system is restarted. A properly sized

anticipator should maintain room temperature within 1

1/2 to 2 degree range.

The anticipator is supplied in the thermostat and is not to

be replaced. If the anticipator should fail for any reason,

the thermostat must be changed.

Содержание DRG0361DL00001S


















































































































Результаты поиска

Содержание DRG0361DL00001S

Отзывы:

Похожие инструкции для DRG0361DL00001S

Бренды по названию

Популярные бренды

Daikin DRG0361DL00001S, Инструкция по эксплуатации

Результаты поиска

Содержание DRG0361DL00001S

Отзывы:

Похожие инструкции для DRG0361DL00001S

Бренды по названию

Популярные бренды