Daikin DCM601A51 Скачать руководство пользователя страница 43

Страница: 43 / 344

User’s Manual EM11A015B

intelligent Touch Manager

4-2

Standard View (Icon) Screen

(8)

(9)

(10)

(11)

(12)

(13)

(14)

(15)

(16)

(17)

(18)

(1)

(2)

(3)

(4)

(5)

(7)

(6)

(1)

Area/Management Point

view area

Displays area and management point icons.

(2)

Menu List

switch button

Switches to the Menu List screen, which consists of Automatic Ctrl., System Settings, Operation

Mgmt. and Energy Navigator (optional) tabs.

The button changes to Close while the Menu List screen is being displayed.

(3)

Standard View

switch button

Switches from the Layout View screen (optional) to the Standard View screen.

(4)

Layout View

switch button

Switches the screen to the Layout View, which displays icons on a floor plan.

Displayed only when the Layout View option is enabled.

NOTE

(5)

Lock/Unlock

button

Locks/Unlocks switching to the Menu List screen.

The button is not displayed when the screen lock is disabled.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды