Daikin DCM601A51 Скачать руководство пользователя страница 29

Страница: 29 / 344

User’s Manual EM11A015B

intelligent Touch Manager

(3)

Touch the

button to move one level up from the currently selected one.

(For detailed operation, see “4-2 Standard View (Icon) Screen”.)

2-3

Starting/Stopping Areas and Management Points

(2)

(1)

Select the area or management point you want to start or stop.

(2)

Selecting “Start” in the

On/Off

combo box starts the selected area or management point while

selecting “Stop” stops the selected area or management point. The icon turns green or red

(depending on the system settings) when the selected area or management point has been started

while the icon turns gray when it is stopped.

(3)

When Confirm is “enabled” in the system settings, a confirmation dialog appears accordingly.

Press the

Yes

button to commit. (For detailed operation, see “6-9 Setting up the Confirm

Operation”.)

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды