Daikin DCM601A51 Скачать руководство пользователя страница 229

Страница: 229 / 344

User’s Manual EM11A015B

intelligent Touch Manager

228

9-4

Remote Maintenance

Remote Maintenance function

Remote maintenance is a function that enables engineers to operate iTM from a remote location

connecting iTM to the Internet with the 3G USB modem. Using this function, they can create or

change the setup of iTM and cope with troubles without going to the site, which saves time and

cost. The following describes how to use this function.

Connecting iTM to the Internet with the 3G USB modem

(1)

Insert the 3G USB modem into the iTM.

(2)

Open “Menu List” after the LED of the modem becomes Green blink.

- The light of LED on the modem indicate as below

• Red light: No radio wave

• Green light: Catching radio wave but not connected

• Green blink: Connected

(3)

Open “Remote Maintenance” screen in “System Settings” tab on the iTM.

- If the modem is not inserted, “Remote Maintenance” button will not appear.

(4)

Select one of the access points shown on the list and push “Connect” to be online.

(5)

Tell the IP address shown in the “IP Address” box to a control engineer.

1. Select an access point

4. Tell the IP address to a control engineer

3. IP address appears

2. Push Connect

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды