Daikin DCM601A51 Скачать руководство пользователя страница 218

Страница: 218 / 344

User’s Manual EM11A015B

intelligent Touch Manager

217

Logging in/out to/from a PC

The Login screen appears when you access the iTM by launching the Web browser on a PC

and entering the IP address of an iTM unit with network settings (http:// iTM IP address ).

(13)

(14)
(15)

The display language of the Login screen follows the iTM unit locale setting.

Enter the user name and password in

(13)

and click the

Login

button

(14)

. The Web Remote

Management screen (Icon view) appears if authentication is successful.

Entering the user name and password, and clicking the

User Setting

button

(15)

displays the

User Setup screen where you can change the login password and set the locale.

(16)

(17)

The

Modify

button

(16)

allows you to change the login password.

(17)

is for setting the locale to be used by the PC. The information you can set is the same as

that of the iTM unit locale setting. Set this as described in “6-5 Setting up the Locale”.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды