Daikin DCM601A51 Скачать руководство пользователя страница 172

Страница: 172 / 344

User’s Manual EM11A015B

intelligent Touch Manager

171

Detailed screen and button descriptions

•

Main Interlocking Control Screen

This screen is displayed when you touch the Interlocking Control button on the Automatic Ctrl.

tab of the Menu List screen (see “4-5 Menu List Screen: Automatic Ctrl. Tab”).

This screen allows you to create and delete interlocking programs, as well as enable/disable the

interlocking programs.

(8)

(1)

(3)
(4)
(5)
(6)
(7)

(2)

(1)

Interlocking program

list

Displays registered interlocking programs.

(2)

Activation

area

Enables and disables an interlocking program.

(3)

Create

button

Creates a new interlocking program. Touching the button displays the Name Input dialog.

The maximum number of interlocking programs you can create is 500.

Set up a name using 1 to 32 characters, irrespective of single or double byte.

Duplicate names are not permitted.

(4)

Copy

button

Copies the program selected in the interlocking program list. Touching the button displays the

Name Input dialog.

(5)

Delete

button

Deletes the program selected in the interlocking program list. Touching the button displays a

deletion confirmation dialog.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды