background image

10

 | 

Maintenance and service

Installer and user reference guide

28

FXSN50~112A2VEB

CO₂ Conveni-Pack: indoor unit

4P602817-1A – 2020.05

10 Maintenance and service

10.1 Precautions for maintenance and service

WARNING: 

  System  contains  refrigerant  under  very  high

pressure.

The system MUST be serviced by qualified persons only.

NOTICE

Maintenance MUST be done by an authorized installer or service agent.

We recommend performing maintenance at least once a year. However, applicable
legislation might require shorter maintenance intervals.

CAUTION: Pay attention to the fan!

It is dangerous to inspect the unit while the fan is running.

Be sure to turn off the main switch before executing any maintenance task.

CAUTION

Do NOT insert fingers, rods or other objects into the air inlet or outlet. When the fan
is rotating at high speed, it will cause injury.

NOTICE

Never  inspect  or  service  the  unit  by  yourself.  Ask  a  qualified  service  person  to
perform this work. However, as end user, you may clean the air filter, suction grille,
air outlet and outside panels.

WARNING

Never replace a fuse with a fuse of a wrong ampere ratings or other wires when a
fuse  blows  out.  Use  of  wire  or  copper  wire  may  cause  the  unit  to  break  down  or
cause a fire.

CAUTION

After  a  long  use,  check  the  unit  stand  and  fitting  for  damage.  If  damaged,  the  unit
may fall and result in injury.

CAUTION

Before accessing terminal devices, make sure to interrupt all power supply.

DANGER: RISK OF ELECTROCUTION

To clean the air conditioner or air filter, be sure to stop operation and turn all power
supplies off. Otherwise, an electric shock and injury may result.

WARNING

Be careful with ladders when working in high places.

Содержание CO2 Conveni-Pack

















































































Отзывы: