background image

15 About the app

Installer and user reference guide

33

BRK+S
Wired remote controller
4P513689-1A – 2018.03

Default values

Field setting default values are different depending on the indoor unit
model.  For  more  information,  see  the  service  manual  of  the  indoor
units. For the following field settings, the default values are the same
for all indoor unit models:

Field setting

Default value

Thermostat sensor

02

Setback

04

Window contact B1

02

Key card contact B2

02

Airflow direction range

02

Remote controller thermostat
sensor

02

Rotation overlap time

03

INFORMATION

▪ The  connection  of  optional  accessories  to  the  indoor

unit  might  cause  changes  to  some  field  settings.  For
more  information,  see  the  installation  manual  of  the
optional accessory.

▪ For details about the specific field settings of each type

of indoor unit, see the installation manual of the indoor
units.

▪ Outdoor  unit  field  settings  can  only  be  configured  via

the  outdoor  unit  PCB.  For  more  information,  see  the
installation manual of the outdoor unit.

▪ Field  settings  that  are  not  available  for  a  connected

indoor unit are not displayed.

15.5.23 Duty rotation

Activate Duty rotation to let the indoor units operate alternately (one
indoor unit alternately inactive), this to increase system lifespan and
reliability.

Duty  rotation  is  designed  for  units  operating  in  critical  applications
(e.g. in server rooms that require lots of cooling). In these cases, the
system  is  equipped  with  an  extra  backup  unit.  Activating  Duty
rotation then allows for:

Rotation

:  because  the  system  is  equipped  with  more  units  than

are  required  to  provide  the  heating/cooling  load,  one  of  the  units
can remain inactive during normal operation. After a set time (i.e.
"Rotation  cycle  time"),  the  inactive  unit  will  start  operation,  and  a
previously  active  unit  will  become  inactive  (i.e.  duty  rotation).
Because  the  units  only  operate  alternately,  the  lifespan  of  the
system increases.

Backup

: having a backup unit allows for system redundancy. If an

active unit goes into error, "Duty rotation" makes sure an inactive
one takes over.

A

A

A

B

A

Inactive backup unit

B

Unit in error

INFORMATION

This function can only be used when the indoor units are in
group control.

INFORMATION

▪ To  let  the  backup  unit  reach  its  cooling/heating

capacity,  an  overlap  period  is  included  in  which  all
indoor  units  are  active.  For  more  information,  see

"Indoor unit field settings" on page 18

 (cfr. field setting

1E-7).

▪ The rotation order depends on the set unit number. For

instructions  on  how  to  change  the  indoor  units'  unit
number, see 

"15.5.18 Unit number" on page 32

.

15.5.24 Test operation

Perform  a  test  run  on  Sky  Air  indoor  units.  During  the  test  run,  the
indoor units cycle through various operation modes and functions to
check if they are ready for operation.

When

Only activate the test operation after the following is completed:

▪ Installation of refrigerant piping;

▪ Installation of drain piping;

▪ Connection of electrical wiring.

Typical workflow

Performing a test operation typically consists of the following stages:

1

Activating the test operation (Madoka Assistant app),

2

Testing  the  indoor  unit  functions  according  to  the  instructions
set out in 

"To perform a test operation" on page 34

,

3

Deactivating the test operation (Madoka Assistant app),

4

Checking the error history for possible errors.

5

If applicable, fixing the causes of those errors.

6

Repeating the procedure if required.

INFORMATION

Also  see  the  installation  manual  of  the  indoor  unit  and
outdoor unit.

Содержание BRC1H519K









































Отзывы: