Daikin BACnet IM 1234-1 Скачать руководство пользователя страница 7

Страница: 7 / 46

nsTallaTIon

www.DaikinApplied.com

IM 1234-1 • BACNET THERMOSTAT

Connecting Inputs

The inputs for the BACnet Thermostat are configured for

specific functions and do not require set up in the field. Not all

inputs are required for every application.

Remote Space Temperature Sensor

(optional)

Connect a 10kΩ, Type II thermistor temperature sensor to

the remote space temperature (RS) input and ground (GND)

terminals. The input includes the internal pull-up resistor.

Follow the instructions supplied with the sensor for installation.
When a remote space temperature input is connected to the

BACnet Thermostat, the remote temperature is used instead of

the internal temperature sensor.

Figure 4: Wiring for Remote Space Temperature Sensor

Discharge Air Temperature

Connect a 10kΩ, Type III thermistor temperature probe to the

discharge air temperature (DAT) input. The input includes the

internal pull-up resistor. Follow the instructions supplied with

the sensor for installation.

Figure 5: Wiring for Discharge Air Temperature Sensor

Fan Status Switch (optional)

Connect a Normally Closed Fan Status switch to the Discharge

Air Temperature (DAT) input and ground (GND) terminals.

The input includes the internal pull-up resistor. Follow the

instructions supplied with the switch for installation.

Figure 6: Wiring for a Fan Status Switch

Water Temperature Sensor

Connect a 10kΩ, Type III thermistor temperature probe to the

water temperature (WST) input. The input includes the internal

pull-up resistor. Follow the instructions supplied with the sensor

for installation.

NOTE:

The water temperature sensor is a required input

sensor for 2-pipe fan coil units.

Figure 7: Wiring for a Water Temperature Sensor

Outside Air Temperature

Connect a 10kΩ, Type III thermistor temperature probe to the

outside air temperature (OAT) input. The input includes the

internal pull-up resistor. Follow the instructions supplied with

the sensor for installation.

Figure 8: Wiring for an Outside Air Temperature Sensor

Содержание BACnet IM 1234-1















































Результаты поиска

Содержание BACnet IM 1234-1

Отзывы:

Похожие инструкции для BACnet IM 1234-1

Бренды по названию

Популярные бренды

Daikin BACnet IM 1234-1, Руководство по установке и обслуживанию

Результаты поиска

Содержание BACnet IM 1234-1

Отзывы:

Похожие инструкции для BACnet IM 1234-1

Бренды по названию

Популярные бренды