background image

IM 1234-1 • BACNET THERMOSTAT 6 

www.DaikinApplied.com

I

nsTallaTIon

I

nsTallaTIon

Installing the BACnet Thermostat

This section provides important instructions and guidelines 

for installing the BACnet Thermostat. Carefully review this 

information before installing the controllers.

Mounting the BACnet Thermostat

For the most accurate performance, install the BACnet 

Thermostat on an inside wall where it can sense the average 

room temperature. Avoid locations with direct sunlight, heat 

sources, windows, air vents, and air circulation or obstructions 

such as curtains, furniture, etc.
The BACnet Thermostat must not be:

•  Mounted on an exterior wall
•  Mounted on or near an object with a large thermal mass 

such as a concrete block wall

•  Blocked from normal air circulation by obstructions
•  Exposed to heat sources such as lights, computers, 

copiers, or coffee makers, or to direct sunlight at any time 

of the day

•  Exposed to drafts from windows, diffusers, or returns
• 

Exposed to air flow through connecting conduits or empty 

spaces behind walls

Rough-in Preparation

Complete rough-in wiring at each location before mounting a 

BACnet Thermostat. This includes the following steps.

•  Install the supplied mounting base directly to a wall, a 

vertical electrical box, or a box with a wall plate kit

•  Routing the connecting cable or cables from the BACnet 

Thermostat to the equipment it is controlling

• 

Block leaks and airflow from conduits with plumber’s putty 

or similar material

•  If replacing an existing thermostat, label existing wires for 

reference when removing the existing thermostat

Figure 2: BACnet Thermostat Mounting Base Details   

Installing the BACnet Thermostat

 CAUTION

Can cause equipment damage .

To prevent mounting screw heads from touching the circuit 

board in the controller, use only the mounting screw supplied 

by Daikin Applied. Using screws other than the type supplied 

may damage the BACnet Thermostat.

To install the controller on a mounting base, do the following:

1.  Turn the Allen screw in the base of the sensor clockwise 

until it clears the case.

2.  Swing the BACnet Thermostat away from the mounting 

base to remove it.

3.  Route wiring for the BACnet Thermostat through the 

mounting base.

4.  Position the base with the embossed UP toward the 

ceiling and fasten it directly to a vertical 2 × 4 inch 

electrical box. 

5.  Connect the wires for the BACnet Thermostat to the 

terminals in the mounting base.

6.  Place the top of the sensor over the top of the mounting 

base and swing it down over the Allen screw bracket. Be 

careful not to pinch any wiring.

7.  Turn the Allen screw counterclockwise until it backs out 

of the mounting base and engages the case.

Figure 3: Allen Head Directions       

Содержание BACnet IM 1234-1















































Отзывы: