Daikin BACnet IM 1234-1 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 46

background image

IM 1234-1 • BACNET THERMOSTAT 44 www.DaikinApplied.com

a

pplICaTIon

d

rawIngs

Heat Pump Unit – Three Heat, Two Cool and Economizer

• Fan status switch (FST) and discharge air temperature

sensor (DAT) are optional. They are typically used only

when the BACnet Thermostat is connected to a network.

• The outdoor air temperature sensor (OAT) is required for

compressor lockout based on outside air temperature.

•  The remote temperature sensor (RS) is optional.
•  For single compressor installations do not connect Y2.
•  If auxiliary heat is not required, do not connect AUX/E.
•  Connect outputs only to 24 volt AC pilot duty inputs.
•  Economizer (ECON) input is 0-10 volts DC.
•  For additional details on connecting sensors, see

Connecting Inputs on page 7

.

Figure 28: Heat Pump Unit Wiring Details—Three Heat, Two Cool and Economizer

«
...
42
43
44
45
46
»

Содержание BACnet IM 1234-1















































Отзывы:

Нет отзывов

Похожие инструкции для BACnet IM 1234-1

Бренд: Fantini Cosmi Страницы: 8

Kitchen thermometer

Бренд: iDevices Страницы: 15

Бренд: ICM Controls Страницы: 2

EgaTronic COD. 51261

Бренд: Ega Master Страницы: 40

Бренд: Daikin Страницы: 23

ACCD LIBERTY Series

Бренд: Daitsu Страницы: 30

Бренд: SK Страницы: 3

Бренд: Inspire Страницы: 10

Бренд: Fantini Cosmi Страницы: 28

Бренд: Daikin Страницы: 2

THERMASGARD RTM

Бренд: domat Страницы: 12

PETIT ULTRAFAST THERMOMETER FOR BABIES

Бренд: Terraillon Страницы: 15

Бренд: Robertshaw Страницы: 4

Бренд: Robertshaw Страницы: 12

Бренд: Robertshaw Страницы: 12

Бренд: Robertshaw Страницы: 24

Comark C12 HACCP

Бренд: Fluke Страницы: 6

Бренд: MESSKO Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды