Daikin ARQ Скачать руководство пользователя страница 11

Страница: 11 / 44

www.DaikinApplied.com 11

IM 1083-3

Louver Installation With Typical Unit

Arrangements – 21⅞" Unit Depth

Figure 14:

21⅞" (556mm) deep full adapter back unit and

floor level outdoor intake louver location

Louver

Field Supplied

Water Piping

Important:

Gasket sealing surface is

required.

Lintel

(By Others)

Unit Refrigerant Piping

Floor Line

1" (25mm)

Sealed Cement

Mortar;Pitch Away

From Unit

Figure 15:

21⅞" (556mm) deep full adapter back unit with

high louver application

Not More Than

28"(711mm)

Sealed Cement

Mortar; Pitch Away

From Unit

Important:

Gasket sealing surface is

required.

Louver

Lintel (By Others)

Unit Refrigerant Piping

Field Supplied

Water Piping

Floor Line

Figure 16:

21⅞" (556mm) partial adapter back unit with

window below unit top (2" step-down) and floor level

outdoor intake louver location

Lintel

(By Others)

Intake Louver

Important:

Gasket sealing

surface is required.

Field-Provided

Water Piping

Insulated, Texture-Painted Top

Floor Line

Sealed Cement

Mortar; Pitch Away

From Unit

(25mm)

21-7/8"

Sash

Not More

Than 12"

Figure 17:

21⅞" (556mm) deep partial adapter back unit

with open refrigerant pipe chase and floor level outdoor

intake louver location

Intake Louver

Not More

Than 12"

Unit Refrigerant Piping

Field Supplied

Water Piping

Important:

Gasket sealing sur-

face is required.

Lintel

(By Others)

Gasket Seal

Floor Line

1" (25mm)

Sealed Cement

Mortar;Pitch Away

From Unit

]

Содержание ARQ













































Результаты поиска

Содержание ARQ

Отзывы:

Похожие инструкции для ARQ

Бренды по названию

Популярные бренды

Daikin ARQ, Руководство по установке и обслуживанию

Результаты поиска

Содержание ARQ

Отзывы:

Похожие инструкции для ARQ

Бренды по названию

Популярные бренды