Daikin ARQ Скачать руководство пользователя страница 10

Страница: 10 / 44

IM 1083-3

10 www.DaikinApplied.com

Louver Installation With Typical Unit

Arrangements – 16⅝" Unit Depth

Figure 10:

The 16⅝˝ (422mm) deep unit with open

refrigerant pipe chase and floor level outdoor intake louver

location

Intake Louver

Floor

Line

Unit Refrigerant Piping

Important:

Gasket sealing

surface is required.

Sealed Cement

Mortar; Pitch

Away From Unit

Lintel

(By Others)

(25mm)

Figure 11:

16⅝" (422mm) deep unit with open refrigerant

pipe chase & above-floor-level outdoor intake louver

application with chased wall

Intake Louver

Floor

Line

Not Less

Than 3"

Not More

Than 21"

Unit Refrigerant Piping

Important:

Gasket sealing

surface is required.

Sealed Cement

Mortar; Pitch

Away From Unit

Lintel (By Others)

(25mm)

CAUTION

Accumulated moisture can cause property damage if not properly

drained. Installing contractor must provide such drainage.

Figure 12: Above floor level outdoor air intake with

accessory closed refrigerant pipe chase

Unit Refrigerant Piping

Floor Line

Lintel (By Others)

Intake Louver

Not Less Than 3"

Not More

Than 28"

Insulated Closure

Plate Accessory

Provide

Drainage

Important:

Gasket sealing

surface is required.

Sealed Cement

Mortar; Pitch Away

From Unit

(25mm)

Figure 13: Floor level outdoor air intake with window

below unit top and 9˝ “finished” (painted) accessory

(insulated) closed refrigerant pipe chase

Lintel (By Others)

Intake Louver

Important:

Gasket sealing

surface is required.

Sash

Unit Refrigerant Piping

Painted, Insulated Closure Plate Accessory

Floor Line

Sealed Cement

Mortar;Pitch Away

From Unit

(25mm)

Содержание ARQ













































Результаты поиска

Содержание ARQ

Отзывы:

Похожие инструкции для ARQ

Бренды по названию

Популярные бренды

Daikin ARQ, Руководство по установке и обслуживанию

Результаты поиска

Содержание ARQ

Отзывы:

Похожие инструкции для ARQ

Бренды по названию

Популярные бренды