Daikin Altherma 3 H HT EPRA14DAW1 Скачать руководство пользователя страница 24

Страница: 24 / 260

About the units and options

Installer reference guide

EPRA14~W1 + ETVH/9W(G)

Daikin Altherma 3 H HT F

4P587502-1A – 2020.01

4.3.2 Possible options for the outdoor unit

Mounting stand (EKMST1, EKMST2)

In colder regions where heavy snowfall can occur, it is recommended to install the
outdoor unit on a mounting frame. Use one of the following models:

▪

EKMST1 with flange feet: to install the outdoor unit on a concrete foundation
where drilling is allowed.

▪

EKMST2 with rubber feet: to install the outdoor unit on foundations where
drilling is not allowed or possible, such as flat roofs or pavements.

For installation instructions, see the installation manual of the mounting stand.

4.3.3 Possible options for the indoor unit

Multi-zoning wired controls

You can connect the following multi-zoning wired controls:

▪

Multi-zoning base unit 230 V (EKWUFHTA1V3)

▪

Digital thermostat 230 V (EKWCTRDI1V3)

▪

Analogue thermostat 230 V (EKWCTRAN1V3)

▪

Actuator 230 V (EKWCVATR1V3)

For installation instructions, see the installation manual of the control, and the
addendum book for optional equipment.

Wireless room thermostat (EKRTR1)

You can connect an optional wireless room thermostat to the indoor unit.

For installation instructions, see the installation manual of the room thermostat
and addendum book for optional equipment.

Remote sensor for wireless thermostat (EKRTETS)

You can use a wireless indoor temperature sensor (EKRTETS) only in combination
with the wireless thermostat (EKRTR1).

For installation instructions, see the installation manual of the room thermostat
and addendum book for optional equipment.

Digital I/O PCB (EKRP1HBAA)

The digital I/O PCB is required to provide following signals:

▪

Alarm output

▪

Space heating/cooling On/OFF output

▪

Changeover to external heat source

For installation instructions, see the installation manual of the digital I/O PCB and
addendum book for optional equipment.

Demand PCB (EKRP1AHTA)

To enable the power saving consumption control by digital inputs you must install
the demand PCB.

For installation instructions, see the installation manual of the demand PCB and
addendum book for optional equipment.

Содержание Altherma 3 H HT EPRA14DAW1




































































































































































































































































Результаты поиска

Содержание Altherma 3 H HT EPRA14DAW1

Отзывы:

Похожие инструкции для Altherma 3 H HT EPRA14DAW1

Бренды по названию

Популярные бренды

Daikin Altherma 3 H HT EPRA14DAW1, Руководство по установке для специалистов

Результаты поиска

Содержание Altherma 3 H HT EPRA14DAW1

Отзывы:

Похожие инструкции для Altherma 3 H HT EPRA14DAW1

Бренды по названию

Популярные бренды