Daikin Altherma 3 GEO EGSAH06UD Series Скачать руководство пользователя страница 12

5 Piping installation

Installation manual

12

EGSAH/X06+10UD

Daikin Altherma 3 GEO

4P598591-1C – 2023.02

5.2.5

To insulate the brine piping

The  piping  in  the  complete  brine  circuit  MUST  be  insulated  to
prevent reduction of the heating capacity.

Consider  that  the  brine  circuit  piping  inside  the  house  can/will
condensate. Foresee adequate insulation for these pipes.

5.3

Connecting water piping

5.3.1

To connect the water piping

NOTICE

Do  NOT  use  excessive  force  when  connecting  the  field
piping  and  make  sure  the  piping  is  aligned  properly.
Deformation of the piping can cause malfunctioning of the
unit.

1

Install  the  shut  off-valve  with  integrated  filter  (delivered  as
accessory) at the space heating/cooling water inlet.

2

Connect the space heating/cooling IN pipe to the shut-off valve
and the space heating/cooling OUT pipe to the unit.

3

Connect the domestic hot water IN and OUT pipes to the indoor
unit. It is obligatory to use the accessory G3 kit EKUHWG3D to
comply  with  UK  legislation.  See 

"5.3.2  To  connect  the  water

piping for domestic hot water"

 [

4

 13].

a b

c d

b

a

Space heating/cooling water OUT (Ø22 mm)

b

Space heating/cooling water IN (Ø22 mm) and shut-off
valve with integrated filter (accessory)

c

Domestic hot water: hot water OUT (Ø22 mm)

d

Domestic hot water: cold water IN (Ø22 mm)

NOTICE

It is strongly recommended to install an additional filter on
the  heating  water  circuit.  Especially  to  remove  metallic
particles from foul heating piping, it is recommended to use
a  magnetic  or  cyclone  filter,  which  can  remove  small
particles.  Small  particles  may  damage  the  unit  and  will
NOT  be  removed  by  the  standard  filter  of  the  heat  pump
system.

NOTICE

About  the  shut-off  valve  with  integrated  filter  (delivered  as
accessory):

▪ The  installation  of  the  valve  at  the  water  inlet  is

mandatory.

▪ Mind the flow direction of the valve.

NOTICE

Expansion  vessel.

  An  expansion  vessel  (field  supply)

MUST be installed on the entering piping before the water
pump within 10 m of the unit.

NOTICE

A  pressure  relief  valve  (field  supply)  with  an  opening
pressure  of  maximum  10  bar  (=1  MPa)  must  be  installed
on the domestic cold water inlet connection in accordance
with the applicable legislation.

NOTICE

▪ A  drain  device  and  pressure  relief  device  must  be

installed  on  the  cold  water  inlet  connection  of  the
domestic hot water cylinder.

▪ To avoid back siphonage, it is recommended to install a

non-return valve on the water inlet of the domestic hot
water tank in accordance with the applicable legislation.
Make sure it is NOT between the pressure relief valve
and the DHW tank.

▪ It is recommended to install a pressure reducing valve

on  the  cold  water  inlet  in  accordance  with  the
applicable legislation.

▪ It is recommended to install an expansion vessel on the

cold  water  inlet  in  accordance  with  the  applicable
legislation.

▪ It is recommended to install the pressure relief valve on

a higher position than the top of the domestic hot water
tank.  Heating  of  the  domestic  hot  water  tank  causes
water  to  expand  and  without  pressure  relief  valve  the
water pressure inside the tank can rise above the tank
design  pressure.  Also  the  field  installation  (piping,
tapping points, etc.) connected to the tank is subjected
to this high pressure. To prevent this, a pressure relief
valve  needs  to  be  installed.  The  overpressure
prevention depends on the correct operation of the field
installed  pressure  relief  valve.  If  this  is  NOT  working
correctly,  overpressure  will  deform  the  tank  and  water
leakage may occur. To confirm good operation, regular
maintenance is required.

NOTICE

▪ It  is  recommended  to  install  shut-off  valves  to  cold

water  IN  and  hot  water  OUT  connections.  Shut-off
valves are field supplied.

However,  make  sure  there  is  no  valve  between  the
pressure  relief  valve  (field  supply)  and  the  DHW
tank.

NOTICE

Install air purge valves at all local high points.

Содержание Altherma 3 GEO EGSAH06UD Series





















































Отзывы: