Daihen OTC Welbee Inverter W400, Руководство пользователя

Страница: 72 / 158

F
UNCTION ON
O
PERATION
P
ANEL
W
ELDING
C
ONDITION
C
HAPTER
6
6-6
6.2 Function on Operation Panel
This section explains the function of displays and keys arranged on the operation panel.
No. Name Function
1 Left digital meter
Displays various information.
• The welding current is displayed in welding, and the LED of "A" lights up.
• In each setting, corresponding setting values are displayed, and the LED lit position
automatically switches.
2 Right digital meter
Displays various information.
• The welding voltage is displayed in welding.
• In each setting, corresponding setting values are displayed, and the LED lit position
automatically switches.
3 Parameter adjustment knob Adjusts each parameter value such as welding current/voltage, and wire feed speed.
4
CURRENT SETTING DISPLAY
SWITCH key
Sets welding current/wire feed speed. The value in setting is displayed on the left digital
meter, which can be adjusted by the parameter adjustment knob. Switching the mode is
enabled by pressing the key.
5
VOLTAGE SETTING DISPLAY
SWITCH key
Set the welding voltage. The value in setting is displayed on the right digital meter, which
can be adjusted by the parameter adjustment knob. When the SYNERGIC mode is
selected for the adjustment mode of welding voltage, pressing this key can switch the
value displayed on the right digital meter between "fine adjustment value" and "actual
voltage value". (In the SYNERGIC mode, the welding voltage according to the welding
current is regarded as ±0, based on which the welding voltage is finely adjusted.)
6 DISPLAY CHANGE SWITCH key
Switches the welding sequence as the set target. During the welding, the display can be
switched to display the value set as the welding condition.
7 F (function) key
Sets the internal function of welding power source. ( 6.7
-
Setting Internal Functions)
Pressing this key for a second or more lights up the LED, and the sequence transits to the
Internal Function Setting mode.
8 GAS CHECK key
Discharges the shield gas. ( 5.3
-
Power ON and Gas Supply)
Pressing this key makes the LED lit, allowing the shield gas to be discharged.
After discharging the gas for approximately 2 minutes automatically stops the discharge.
Pressing this key again lights off the LED, stopping the shield gas discharge.
9 WIRE INCH key
Feeds the wire. ( 5.4
-
Wire Inching)
The LED lights during when the key is pressing, allowing the wire to be fed.
The feeding speed can be adjusted by the parameter adjustment knob.
When the analog remote control (optional) is connected, the speed can be adjusted by the
welding current setting knob.
0.8
Is IE
I
OP
0.9
1.0
1.2
1.6
1.4
F
A
m/min.
V
s
A V
s
㸣
V
OP1
OP2
sec.
Hz
m/min.
JOB No.
SYN.
INDIV.
SYNERG. WAVE
(3 sec.)
LOAD
SAVE
ARC START
ENTER
DC NO-LOAD VOLTAGE
Al/99
Al/Mg
Cu Si
Cu Al
G3Si1
G3Si1(Fill)
CrNi
CrNi(Ferr)
CrNi(Fill)
INCONEL
TITANIUM
OP1
OP2
OP3 MIG (100%Ar)
MIG (2.5%CO
2
)
MIG (2%O
2
)
MAG (20%CO
2
)
MAG (10%CO
2
)
OP1
OP2
AC PULSE
AC WAVE PULSE
DC PULSE
DC WAVE PULSE
DC
DC TIG
DC STICK
29
16
9
8
7
24
25
26
4
5
1 2
27
6
17
18
23
3
21 22
15 14 13 12 11
28
10
20 19