background image

Regulatory  Information    V 

Regulatory Information 

The  regulatory  information  herein  might  vary  according  to  the  model  you  purchased.  Some 

information is only applicable for the country or region where the product is sold. 

FCC Information 

 

Changes  or  modifications  not  expressly  approved  by  the  party  responsible  for  compliance 

could void the user's authority to operate the equipment. 

FCC conditions: 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 

conditions: 

 

This device may not cause harmful interference. 

 

This device must accept any interference received, including interference that may cause 

undesired operation. 

FCC compliance: 

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  digital  device, 

pursuant  to  part  15  of  the  FCC  Rules.  This  equipment  generate,  uses  and  can  radiate  radio 

frequency energy and, if not installed and used in accordance with the instructions, may cause 

harmful interference to radio communication. 

 

For  class  A  device,  these  limits  are  designed  to  provide  reasonable  protection  against 

harmful  interference  in  a  commercial  environment.  Operation  of  this  equipment  in  a 

residential  area  is  likely  to  cause  harmful  interference  in  which  case  the  user  will  be 

required to correct the interference at his own expense. 

 

For  class  B  device,  these  limits  are  designed  to  provide  reasonable  protection  against 

harmful  interference  in  a  residential  installation.  However,  there  is  no  guarantee  that 

interference will not occur in a particular installation. If this equipment does cause harmful 

interference  to  radio  or  television  reception,  which  can  be  determined  by  turning  the 

equipment off and on, the user is encouraged to try to correct the interference by one or 

more of the following measures: 

  Reorient or relocate the receiving antenna. 

  Increase the separation between the equipment and receiver. 

  Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the 

receiver is connected. 

  Consult the dealer or an experienced radio/TV technician for help. 

Содержание Ultra IPC-HDBW7442H-ZFR





















Отзывы: