Dahua Technology IPC-HDW5449H-ASE-D2-0280B Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 18

background image

Quick Start Guide

7

Figure 3-3 Dimensions: Model B (Unit: mm [inch])

3.3 Installing the Camera

3.3.1 Installation Methods

Figure 3-4 Installation methods

3.3.2 (Optional) Installing the SD Card

●

SD card slot is available on select models.

●

Disconnect the power before installing or removing the SD card.

Press the reset button for 10 seconds to reset the device.

«
...
12
13
14
15
16
...
»

Содержание IPC-HDW5449H-ASE-D2-0280B



















Отзывы:

Нет отзывов

Похожие инструкции для IPC-HDW5449H-ASE-D2-0280B

Бренд: Banner Страницы: 98

Бренд: Ubiquiti Страницы: 24

Бренд: ACS Страницы: 64

Бренд: PRODIS Страницы: 12

Motion Sensor Alarm

Бренд: Tiiwee Страницы: 35

Бренд: usi Страницы: 10

vdp20 vandal dome

Бренд: deView electronics Страницы: 2

Бренд: Siqura Страницы: 2

Бренд: Alecto Страницы: 76

Бренд: Abus Страницы: 4

Бренд: Olympus Страницы: 2

Бренд: jablotron Страницы: 2

Pro Alarm System AP5500

Бренд: ELRO Страницы: 8

Бренд: Eldes Страницы: 8

Бренд: Nexxt Страницы: 10

Бренд: Spartan Страницы: 18

ELI-IP5-VD31-312MR

Бренд: e-Line Technology Страницы: 94

paddy 000121300000

Бренд: Menabo Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды