Dahua Technology DHI-IVSS7008 Скачать руководство пользователя страница 252

Страница: 252 / 381

User's Manual

232

Parameters

Description

Cache strategy

Set cache strategy of remote device video stream.

●

Self-adaptive: System automatically adjusts video stream cache

status according to the network bandwidth.

●

Realtime: Guarantee video real-timeness. When the network

bandwidth is not sufficient, the video might not be fluent.

●

Fluency: Guarantee video fluency. When the network bandwidth is

not sufficient, the video might not be clear.

Step 6

Click Save.

Step 7

(Optional) Click

, and then you can go to the web interface of the remote device.

On the local interface of the Device, you cannot click

to go to the web interface of the

remote device.

8.2.2.3.3 Configuring Video Parameters

Set different video parameters according to different bit stream types based on the bandwidth.
Step 1

Click

, or click

on the configuration page, and then select DEVICE.

Step 2

Select a remote device on the left panel and then click Video tab.

Figure 8-11 Video

Step 3

Set main stream, sub stream 1, or sub stream 2.

Step 4

Set general video quality parameters.

Table 8-4 Video parameters description

Parameters

Description

Smart Codec

Enable this function to enhance performance of video compression and
thus reduce storage space requirement.

This function is only available for main stream.

Содержание DHI-IVSS7008






























































































































































































































































































































































































Результаты поиска

Содержание DHI-IVSS7008

Отзывы:

Похожие инструкции для DHI-IVSS7008

Бренды по названию

Популярные бренды

Dahua Technology DHI-IVSS7008, Руководство пользователя

Результаты поиска

Содержание DHI-IVSS7008

Отзывы:

Похожие инструкции для DHI-IVSS7008

Бренды по названию

Популярные бренды