Daewoo Solar 300LC-V Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 658

background image

S0102000
Page 6

Track Excavator Safety

GENERAL SAFETY ESSENTIALS

ACCESSORY APPLICATIONS

The excavator has been primarily designed for moving earth with a bucket. For use as a grapple or for
other object handling, contact Daewoo for proper installation and application. Lifting-work applications
(unless restricted or prohibited by local regulations) are permitted in approved lift configuration, to rated
capacity only, with no side-loading. DO NOT use the machine for activities for which it was not intended.
DO NOT use the bucket for lifting work, unless lift slings are used in the approved configuration.

Use of an accessory hydraulic hammer (breaker), work in rough terrain, demolition applications or other
hazardous operation may require installation of additional protective structures to safeguard the operator.

LIFTING CAPACITY RATING CONFIGURATION

Lifting capacity ratings that are printed at the end of this safety section are based on the machine being
level, on a firm supporting surface, with hooks and slings attached in approved configuration. Loads must
be balanced and supported evenly. Use taglines to keep the load steady if wind conditions and large
surface area are a problem. Work crew hand signals, individual tasks and safe procedures should all be
universally understood before the lift is made.

LOCATION OF SAFETY LABELS

Location of safety labels (decals) can vary from unit to unit. Refer to appropriate Operation and
Maintenance Manual, and parts manual for your unit.

Always replace damaged or faded decals.

IMPORTANT

Before using the excavator to make lifts check municipal and regional regulations or statutes
that could apply. Governing ordinances may require that all heavy lifting be done with single
purpose equipment specifically designed for making lifts, or other local restrictions may apply.
Making heavy lifts with a general purpose excavator that can be used for digging, loading,
grading or other work may be expressly forbidden by a regional injunction or other legal
prohibition. Always follow all of the other instructions, guidelines and restrictions for Safe
Lifting in the Operation and Maintenance Manuals.

«
...
12
13
14
15
16
...
»

Содержание Solar 300LC-V



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Solar 300LC-V

Бренд: PREMAS Страницы: 44

Бренд: Takeuchi Страницы: 20

Бренд: OLEO Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды