background image

25

8. TROUBLE SHOOTING GUIDE

PROBLEM

WATER IS 

NOT SUP-

PLIED.

CHECK POINT

Do you open the water

tap?

Is the filter of the water

inlet valve clogged with

dirt?

Is the water pressure

sufficient?

(0.3~8 kgf/cm

2

)

Does the water inlet

valve make operating

sound?

Is the connector or the

terminal connected

properly?

Is the output voltage of

the P.C.B normal?

CAUSE

Water inlet valve

is defective.

Improper connection of

the connector or the ter-

minal.

P.C.B AS is defective.

Lead wire is defective.

SOLUTION

Change water inlet valve.

Open the water tap.

Clean the filter.

Increase the water pres-

sure.

Connect the connector or

the terminal properly.

Change the P.C.B AS.

Change the lead wires.

NO

YES

NO

YES

NO

YES

YES

YES

YES

NO

NO

NO

NOTE : Open the water tap fully and measure 

the flow rate.

From the upper results, you know that the flow rate more than

11.5

l

/min. is essential for water supply.

Flow

11.5

15.0

18.0

20.3

24.1

27.4

rate(

l

/min.)

Water pressure

0.3

0.4

0.5

0.6

0.8

1.0

(Kgf/cm

2

)

1. When replace the P.C.B. ASS’Y do not scratch the surface of the P.C.B. ASS’Y.
2. Disconnect the power cord from the electric outlet.

NOTES

Concerning Water Supply

Содержание DWF-170M














































Отзывы: