Dacor Discovery DYRP48DSNGH, Руководство по установке

Страница: 21 / 22

19
Installation Instructions
Verifying Proper Operation
Before operating the range, read the accompanying use and
care manual completely. It contains Important safety, service and
warranty information.
1. Before beginning the test procedure, ensure that all cooktop
control valves are in the OFF position, and all burner rings,
burner caps, and grates are properly positioned on the
cooktop frame.
2. Turn on the gas supply at the shut-off valve. Check for gas
leaks.
3. Turn on power to the range at the circuit breaker or fuse box.
4. Follow the prompts on the oven’s display to set up the user
preferences and wireless network settings.
5. Touch the
MENU
key on the display.
6. Touch the BAKE key on the display. The default bake
temperature should appear on the display .
7. Touch Start . After 3 minutes, open the door to make sure the
air inside the oven has begun to heat.
8. The display should show BAKE , and the preheating
temperature.
9. Touch CANCEL-SECURE or CANCEL RIGHT on model
DYRP48D to stop the oven heating process.
10. Test one of the burners by pushing the knob in and turning it
counterclockwise to the HIGH position. It may take up to four
seconds for ignition to occur, at which time the ignitor will stop
sparking. If ignition does not occur
within four seconds, turn off the
knob, wait for at least five minutes
to allow any gas to dissipate,
then repeat the ignition test. After
ignition, rotate the control knob
counterclockwise from HIGH to
LOW to adjust the flame height
progressively. When the range is
installed properly, the flame will be
steady and quiet. It will also have
a sharp, blue inner cone that will
vary in length proportional to the burner size. Dacor’s Smart
Flame™ feature reduces the flame under the grate fingers to
increase grate life. If the range is equipped for use
with LP gas, the ends of the flame may be yellow
at the tips, which is normal.
11. Turn the control knob to the OFF position.
12. Repeat the ignition test for all remaining burners.
If the range does not operate properly, follow these
troubleshooting steps:
1. Verify that power and gas are supplied to the range.
2. Check the electrical connections and gas supply to ensure
that the installation has been completed correctly.
3. Repeat the above bake test or burner ignition test.
4. If the appliance still does not work, contact Dacor Distinctive
Service at (800) 793-0093 ex. 2822. Do not attempt to repair
the appliance yourself. Have the model and serial numbers
available when you call. See page II for location.
Dacor is not responsible for the cost of correcting problems
caused by a faulty installation.
Removing the Range for Service
1. Turn the gas supply valve to the off position.
2. Turn off power to the range at the circuit breaker panel or
fuse box.
3. Pull the range out from the wall
Reinstalling the Range After
Service
1. Push the range into operating position, making sure the anti-
tip bracket is engaged (see page 16).
2. Turn on power to the range at the circuit breaker panel or
fuse box.
3. Turn the gas supply valve to the on position.
Installation Checklist
WARNING
• To ensure a safe and proper installation, the following
checklist should be completed by the installer to ensure
that no part of the installation has been overlooked.
• Proper installation is the responsibility of the homeowner.
The importance of proper installation of your Dacor range
cannot be overemphasized.
□ Has the plastic coating been peeled off the outside of the
range? Have all packaging materials been removed from
inside the oven?
□ Are all leveling legs extended down to make contact with the
floor? Is the unit level? See page 16.
□ Is the range secured in place with the provided anti-tip
bracket and foot according to these instructions? See pages
7 and 16.
□ Is the range wired and grounded according to these
instructions and in accordance with all applicable electrical
codes? Has the electrical access cover been replaced? See
pages 4 and 10 to 15.
□ Has the gas supply inlet pressure been measured to ensure
that it does not exceed the maximums stated in these
instructions. See page 4.
□ Is the range connected to the gas supply according to these
instructions and in accordance with all applicable codes?
Did the installer check the gas supply for leaks? Has the gas
regulator cover been re-installed? See page 15.
□ Is the oven door properly installed according to these
instructions? See page 16.
□ Have the burner knobs been installed in the proper locations?
See page 17.
□ Are the burners and grates properly installed according to
these instructions? See page 18.
□ Has proper operation been verified? Has the warranty
been activated on-line or the warranty card been filled out
completely and mailed?
OFF Icon
Normal Flame