Da-Lite ViewShare Advantage Electrol Retrofit страница 2 Скачать руководство пользователя | Manualshive

Страница: 2 / 20

background image

2

Tools Required for Installation

Important Safety Instructions

When using your video equipment, basic safety precautions
should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating at

least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by the

manufacturer may cause a risk of fire, electric shock, or injury to
persons.

Pre-Installation

Prior to Retrofit installation, you will need to run a CAT5 or
CAT5e network cable from the motor end of your screen to
the area in which your computer will be located. THE CAT5
CABLE IS NOT PROVIDED. The length of the CAT5 cable cannot
exceed 200 feet. See Pre-Installation of ViewShare Screen and
Roller Assembly and Camera and Speakerphone Installation
sections for additional details on CAT5 cable connections.

NOTE:

It requires at least two people to install a ViewShare

Retrofit.

7/16“ Socket Driver

with 6" Extension

1/8” Hex Key

(included)

#2 Phillips Screwdriver

«
1
2
3
4
...
»

Содержание ViewShare Advantage Electrol Retrofit





















Отзывы:

Нет отзывов

Похожие инструкции для ViewShare Advantage Electrol Retrofit

Бренд: Acer Страницы: 2

Бренд: NEC Страницы: 6

Бренд: NEC Страницы: 6

Бренд: Zenith Страницы: 56

Бренд: Zenith Страницы: 60

Бренд: Zenith Страницы: 36

Бренд: BenQ Страницы: 124

Бренд: Costway Страницы: 28

Бренд: Optoma Страницы: 93

Бренд: Optoma Страницы: 75

HIGHlite 4000Dsx

Бренд: NEC Страницы: 53

Бренд: Hitachi Страницы: 40

Бренд: iGGUAL Страницы: 12

LEDPAR641884IN1

Бренд: ProLights Страницы: 36

Бренд: Hitachi Страницы: 26

Бренд: Hitachi Страницы: 2

Бренд: Hitachi Страницы: 2

Бренд: Hitachi Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды