D-Link DVG-7111S Скачать руководство пользователя страница 73

Страница: 73 / 95

DVG-7111S

User’s Manual

MAINTENANCE

D-Link Systems, Inc.

3-3 MAINTENANCE

3-3-1 Device Management

MAINTENANCE

→

Device Management

Note:

There are two operating levels when entering the Web UI. Logging-in as the ADMIN allows you to

change all settings. A Web UI USER only has access to some settings.

Password:

By default there is no password configured. It is highly recommended that you create a

password to keep your router secure.

MAINTENANCE

→

Device Management

Port of Web Access from WAN:

Enter the port number when accessing the web-based configuration

utility from the WAN port.

Web Idle Time Out:

Enter the range of effective time when log-in the web interface. The user will be

disconnected from the web page to allow others to log-in.

Enable Web UI:

Check the box to enable WEB access from WAN or LAN.

Enable Telnet Service:

Check the box to enable Telnet access from WAN or LAN.

Allow ICMP Request From WAN

Содержание DVG-7111S
































































































Результаты поиска

Содержание DVG-7111S

Отзывы:

Похожие инструкции для DVG-7111S

Бренды по названию

Популярные бренды

D-Link DVG-7111S, Руководство пользователя

Результаты поиска

Содержание DVG-7111S

Отзывы:

Похожие инструкции для DVG-7111S

Бренды по названию

Популярные бренды