D-Link DVG-7111S Скачать руководство пользователя страница 27

Страница: 27 / 95

DVG-7111S

User’s Manual

SETUP

D-Link Systems, Inc.

3-1-3 LAN Settings

SETUP

→

LAN Setup

Interface Mode:

Select the VoIP TA serving as a

Router

with NAT or

Bridge

between WAN port and

LAN port without NAT.

Note:

It is still accessible if LAN Interface Mode is Bridge.

LAN Port Address:

Enter the LAN IP address of the VoIP TA. It is also the default gateway for DHCP

clients.

Subnet Make:

Enter the subnet mask for DHCP clients.

Enable DHCP Server:

This variable is to assign the IP address for the devices connected to LAN port

of the VoIP TA.

IP Pool Starting Address:

Enter the starting IP address for the DHCP server's IP assignment.

IP Pool Ending Address:

Enter the ending IP address for the DHCP server's IP assignment.

IP Pool Uses Other Default Gw:

Check the box to assign different default gateway for DHCP clients.

IP Pool Default Gateway:

Enter the new default gateway that is different from LAN IP of the VoIP TA.

IP Pool Subnet mask:

Enter the new subnet mask.

Содержание DVG-7111S
































































































Результаты поиска

Содержание DVG-7111S

Отзывы:

Похожие инструкции для DVG-7111S

Бренды по названию

Популярные бренды

D-Link DVG-7111S, Руководство пользователя

Результаты поиска

Содержание DVG-7111S

Отзывы:

Похожие инструкции для DVG-7111S

Бренды по названию

Популярные бренды