D-Link DPN-1021G Скачать руководство пользователя страница 94

Страница: 94 / 145

DPN-1021G

GPON ONT VoIP Gateway with 1 GPON

Port, 1 10/100/1000Base-T Port, 1 10/100Base-TX Port,
and 1 FXS Port

User Manual

Configuring via Web-based Interface

VoIP

In this menu you can configure all parameters essential for VoIP via SIP and specify all needed
settings for the phone connected to the gateway.

Basic Settings

On the

VoIP / Basic Settings

page, you can configure all needed settings for VoIP via SIP.

Figure 71. The

VoIP / Basic Settings

page.

Parameter

Description

SIP Proxy

Address

An IP or URL address of the SIP proxy server.

Port

A port of the SIP proxy server. Unless another setting is given by
your ISP, it is recommended to leave the default value (

5060

SIP Outbound Proxy

Address

An IP or URL address of the SIP outbound proxy server.

Port

A port of the SIP outbound proxy server. Unless another setting is
given by your ISP, it is recommended to leave the default value
(

5060

SIP Domain

Use domain to register

Move the switch to the right if your ISP requires to specify a domain
name upon registration on the SIP proxy server. Then fill in the

SIP

domain name

field.

Page

of 145

Содержание DPN-1021G


















































































































































Результаты поиска

Содержание DPN-1021G

Отзывы:

Похожие инструкции для DPN-1021G

Бренды по названию

Популярные бренды

D-Link DPN-1021G, Руководство пользователя

Результаты поиска

Содержание DPN-1021G

Отзывы:

Похожие инструкции для DPN-1021G

Бренды по названию

Популярные бренды