D-Link DPN-1021G Скачать руководство пользователя страница 68

Страница: 68 / 145

DPN-1021G

GPON ONT VoIP Gateway with 1 GPON

Port, 1 10/100/1000Base-T Port, 1 10/100Base-TX Port,
and 1 FXS Port

User Manual

Configuring via Web-based Interface

MVR

On the

Advanced / MVR

page, you can allow using MVR technology.

MVR technology (

Multicast VLAN Registration

) allows a server located in one VLAN to transmit

multicast stream to clients located in other VLANs.

Figure 51. The

Advanced / MVR

page.

You can specify the following parameters:

Parameter

Description

IPv4/IPv6

Enable MVR

Move the switch to the right to allow using MVR technology for the
relevant protocol.

VLAN ID

An identifier of the VLAN which transmits multicast traffic.

Priority

A priority tag for multicast traffic.

LAN ports

Select the checkboxes corresponding to the ports to which multicast
traffic will be transmitted.

Click the

APPLY

button.

Page

of 145

Содержание DPN-1021G


















































































































































Результаты поиска

Содержание DPN-1021G

Отзывы:

Похожие инструкции для DPN-1021G

Бренды по названию

Популярные бренды

D-Link DPN-1021G, Руководство пользователя

Результаты поиска

Содержание DPN-1021G

Отзывы:

Похожие инструкции для DPN-1021G

Бренды по названию

Популярные бренды