D-Link DPN-1021G Скачать руководство пользователя страница 65

Страница: 65 / 145

DPN-1021G

GPON ONT VoIP Gateway with 1 GPON

Port, 1 10/100/1000Base-T Port, 1 10/100Base-TX Port,
and 1 FXS Port

User Manual

Configuring via Web-based Interface

Advanced

In this menu you can configure advanced settings of the gateway:

•

create groups of ports for VLANs

•

allow using MVR technology

•

view physical parameters of the gateway transmitter and the status of synchronization with
the OLT device and specify data for authorization

•

allow the gateway to connect to a private Ethernet line

•

add name servers

•

configure autonegotiation or manually configure speed and duplex mode for each Ethernet
port of the gateway

•

configure notifications on the reason of the Internet connection failure

•

configure a DDNS service

•

define static routes

•

configure TR-069 client

•

create rules for remote access to the web-based interface

•

enable the UPnP IGD protocol

•

allow the gateway to use IGMP, RTSP, enable the SIP ALG, and the
PPPoE/PPTP/L2TP/IPsec pass through functions

•

configure VPN tunnels based on IPsec protocol.

Page

of 145

Содержание DPN-1021G


















































































































































Результаты поиска

Содержание DPN-1021G

Отзывы:

Похожие инструкции для DPN-1021G

Бренды по названию

Популярные бренды

D-Link DPN-1021G, Руководство пользователя

Результаты поиска

Содержание DPN-1021G

Отзывы:

Похожие инструкции для DPN-1021G

Бренды по названию

Популярные бренды