background image

DPN-1021G

  GPON   ONT  VoIP Gateway   with   1   GPON

Port, 1 10/100/1000Base-T Port, 1 10/100Base-TX Port,
and 1 FXS Port

User Manual

Configuring via Web-based Interface

URL Filter

On the 

Firewall / URL Filter

 page, you can specify restrictions on access to certain web sites.

Figure 92. The 

Firewall / URL Filter 

page.

To enable the URL filter, in the 

General Settings

 section, move the 

Enable

 switch to the right,

then select the needed mode from the 

Type

 drop-down list:

Block listed URLs

: when this value is selected, the gateway blocks access to all addresses

specified in the 

Filters

 section;

Block all URLs except listed

: when this value is selected, the gateway allows access to

addresses specified in the 

Filters

 section and blocks access to all other web sites.

Click the 

APPLY

 button.

To specify URL addresses to which the selected filtering mode will be applied, in the  

Filters

section, click the 

ADD RULE

 button and enter a relevant address in the displayed line. Then click

the 

APPLY

 button.

To remove an address from the list of URL addresses, click the 

Delete

 icon ( ) in the line of the

relevant URL address. Then click the 

APPLY

 button.

Page 

125

 of 145

Содержание DPN-1021G


















































































































































Отзывы: