D-Link DIR-300A Скачать руководство пользователя страница 13

Страница: 13 / 181

DIR-300A

Wireless N150 Router

User Manual

Overview

Back and Bottom Panels

Figure 2. Back panel view.

Name

Description

12VDC IN

Power connector.

POWER

A button to turn the router on/off.

INTERNET

A port to connect

to a cable or DSL modem or to a private Ethernet line

(it is recommended to use the cable included in the delivery package).

LAN 1-4

4 Ethernet ports to connect computers or network devices.

WPS

A button to set up a secure wireless connection (the WPS function) and
enable/disable the wireless network.

To use the WPS function: with the device turned on, push the button,
hold it for 2 seconds, and release. The

WLAN / WPS

LED should start

blinking.

To disable the router's wireless network: with the device turned on, press
the button, hold for 7 seconds, and release. The

WLAN / WPS

LED

should turn off.

Page

of 181

Содержание DIR-300A






















































































































































































Результаты поиска

Содержание DIR-300A

Отзывы:

Похожие инструкции для DIR-300A

Бренды по названию

Популярные бренды

D-Link DIR-300A, Руководство пользователя

Результаты поиска

Содержание DIR-300A

Отзывы:

Похожие инструкции для DIR-300A

Бренды по названию

Популярные бренды