manualshive.com logo in svg

D-Link DGS-2000 Series, Справочное руководство

Поделиться
Скачать
D-Link DGS-2000 Series Скачать руководство пользователя страница 88

4  Web-based Switch Configuration

  

D-Link DGS-2000 Series Ethernet Switch User Manual 

8

8

1

1

 

 

 

Figure 4.107 – QoS > Bandwidth Control 

 

From Port / To Port:

 A consecutive group of ports may be configured starting with the selected port. 

Type:

  This drop-down menu allows user to select between 

RX 

(receive), 

TX 

(transmit), and 

Both

. This 

setting will determine whether the bandwidth ceiling is applied to receiving, transmitting, or both receiving 

and transmitting packets. 

No Limit:

 This drop-down menu allows user to specify that the selected port will have no bandwidth limit. 

Enabled 

disables the limit. 

Rate 16-1000000):

 This field allows user to enter the data rate, in Kbits per second, will be the limit for the 

selected port. The value is between 63 and 1024000. 
 
Click 

Apply 

to set the bandwidth control for the selected ports. 

 

 

NOTE:

 The TX rate for Gigabit ports can only be 

configured in multiples of 1850kbps. If any other 

value is used, the system automatically rounds it 

down to the lower multiple of 1850. 

 

QoS > QoS Settings 

This page allows user to configure Qos port priority and queue mechanism. 

 

Содержание DGS-2000 Series

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды