manualshive.com logo in svg

D-Link DGS-2000 Series, Справочное руководство

Поделиться
Скачать
D-Link DGS-2000 Series Скачать руководство пользователя страница 12

1  Product Introduction

  

D-Link DGS-2000 Series Ethernet Switch User Manual 

5

5

 

 

DNA3.x.x.x)) to download the image or call D-Link Technical 

Support for further help. 

 

Rear Panel 

 

Figure 1.4 – DGS-2000-10P Rear Panel 

 

Power:

 Connect the supplied AC power cable to this port. 

 

DGS-2000-10MP 

8-Port 10/100/1000Mbps, plus 2 SFP Ports (100/1000Mbps)  Ethernet PoE switch. 
 

Front Panel 

 

Figure 1.5 – DGS-2000-10MP Front Panel 

 

The front panel of the 

DGS-2000-10MP

 switch consists out of the following:

 

•

 

Power LED : 

The Power LED lights up when the Switch is connected to a power source. 

•

 

Fan Error: 

The FAN LED shows the status of the fans, light off indicates all fans work fine and the red 

light indicates that one or multiple fans are working abnormally. 

 

•

 

PoE Max:

 The solid amber of PoE Max LED indicates the Switch reaches the maximum power budget 

defined by the administrator via PoE System Settings page of Web GUI or the default power budget of 

130 Watts. The blinking amber of PoE Max LED represents the switch is in guradband mode (available 

power left is less 7 watts). 

•

 

Port Link/Act/Speed LED (1-8):

  The Link/Act/Speed LED flashes, which  indicates a network link 

through the corresponding port. Blinking indicates that the Switch is either sending or receiving data to 

the port. When a port has an amber light, this indicates that the port is running on 10M or 100M. When 

it has a green light it is running on 1000M. 

•

 

Port Link/Act/Speed LED (9F-10F):

 The Link/Act/Speed LED flashes, which indicates a network link 

through the corresponding port. Blinking indicates that the Switch is either sending or receiving data to 

the port. When the port LED glows in amber, it indicates the port is running on 100M. When the port 

LED glows in green, it is running on 1000Mbps. 

•

 

Mode:

 By pressing the Mode button, the Port LED will switch between 

Link/Act

 and 

PoE

 modes. 

•

 

Reset:

 Press the Reset button for 1~5 seconds to reset the Switch back to the default settings and led 

will be solid light with amber for 1 second. 
 

 

CAUTION:

  The MiniGBIC ports should use UL  listed Optical 

Transceiver product, Rated Laser Class I. 3.3Vdc. 

 

 

Si le transceiveur optique n'est pas livré avec l'appareil, le manuel 

d'utilisation doit comporter la description ci-dessous ou son 

équivalent :« Ce produit est destiné à être utilisé avec un 

transceiveur optique homologué UL,tension DC3.3V, classe laser 

Содержание DGS-2000 Series

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды