D-Link DGS-1250 Series страница 106 Скачать руководство пользователя | Manualshive

Страница: 106 / 312

background image

DGS-1250 Series Gigabit Ethernet Smart Managed Switch Web UI Reference Guide

97

Link Aggregation

Understanding Port Trunk Groups

Port trunk groups are used to combine a number of ports together to make a single high-bandwidth data pipeline. The
Switch supports up to 32 port trunk groups with up to 12 ports in each group.

Figure 5-41 Example of Port Trunk Group

The Switch treats all ports in a trunk group as a single port. Data transmitted to a specific host (destination address)
will always be transmitted over the same port in a trunk group. This allows packets in a data stream to arrive in the
same order they were sent.

Link aggregation allows several ports to be grouped together and to act as a single link. This results in a bandwidth
that is a multiple of a single link's bandwidth.

Link aggregation is most commonly used to link bandwidth intensive network devices, such as servers, to the
backbone of a network.

The Switch allows the creation of up to 32 link aggregation groups, each group consisting of up to 12 links (ports).
Each port can only belong to a single link aggregation group.

Load balancing is automatically applied to the ports in the aggregated group, and a link failure within the group causes
the network traffic to be directed to the remaining links in the group.

The Spanning Tree Protocol will treat a link aggregation group as a single link. If two redundant link aggregation
groups are configured on the Switch, STP will block one entire group; in the same way, STP will block a single port
that has a redundant link.

NOTE:

If any ports within the trunk group become disconnected, packets intended for the

disconnected port will be load shared among the other linked ports of the link aggregation
group.

«
...
104
105
106
107
108
...
»

Содержание DGS-1250 Series

























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DGS-1250 Series

Бренд: Campbell Hausfeld Страницы: 12

Бренд: H3C Страницы: 32

Бренд: H3C Страницы: 22

Бренд: H3C Страницы: 488

Бренд: H3C Страницы: 3

Бренд: H3C Страницы: 8

Бренд: H3C Страницы: 25

Бренд: H3C Страницы: 31

Бренд: H3C Страницы: 23

Бренд: H3C Страницы: 24

Бренд: H3C Страницы: 126

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 32

Бренд: H3C Страницы: 13

Бренд: H3C Страницы: 16

Бренд: H3C Страницы: 39

Бренд: Lantronix Страницы: 40

Бренд: Lantronix Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды