
Installing the Hardware
25
word
is blank.
The DES-3226L is installed and loaded with the default configuration.
4.
Reduce network traffic by turning off the Network Configuration Protocol. Enter the following
command:
configure network protocol none
5.
Set the IP address, subnet mask, and gateway address by issue the following command:
config network parms
ipaddress netmask gateway
IP Address
Unique IP address for the DES-3226L. Each IP parameter is made up of four decimal numbers,
ranging from 0 to 255. The default for all IP parameters is zeroes (0.0.0.0).
Subnet
Subnet mask for the LAN.
gateway
IP address of the default router, if the switch is a node outside the IP range of the LAN.
6.
To enable these changes to be retained during a reset of the DES-3226L, type
Ctrl-Z
to return to
the main prompt, type
save config
at the main menu prompt, and type
y
to confirm the changes.
7.
To view the changes and verify in-band information, issue the command:
show network
.
8.
The DES-3226L is configured for in-band connectivity and ready for Web-based management.
Configuring for Out-Of-Band Connectivity
To monitor and configure the switch using out-of-band connectivity, use the console port to
connect the switch to a terminal desktop system running terminal emulation software. The
console port connector is a male DB-9 connector, implemented as a data terminal equipment
(DTE) connector.
Figure 6.
D-Link DES-3226L - Front View
The following hardware is required to use the console port:
z
VT100-compatible terminal, or a desktop, or a portable system with a serial port running
VT100 terminal emulation software.
z
An RS-232 crossover cable with a female DB-9 connector for the console port and the
appropriate connector for the terminal.
Perform the following tasks to connect a terminal to the switch console port using out-of-band
connectivity:
1.
Connect an RS-232 crossover cable to the terminal running VT100 terminal emulation software.
2.
Configure the terminal emulation software as follows:
A. Select the appropriate serial port (serial port 1 or serial port 2) to connect to the console.
B. Set the data rate to 115,200 baud.
Содержание DES-3226L
