D-Link DAP-1533 Скачать руководство пользователя страница 66

Страница: 66 / 99

D-Link DAP-1533 User Manual

Section 4 - Security

Configure WPA/WPA2

It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish

wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the

added overhead.

1. Log into the web-based configuration by opening a web browser

and entering the IP address of the access point (192.168.0.50). Click

on Setup and then click

Wireless.Settings

on the left side.

2. Next to

Security Mode

section, select

Enable.WPA.Wireless.

Security.(enhanced)

from the drop-down menu.

3. Next to

Cipher Type

, select

TKIP

AES

, or

Auto.(TKIP/AES)

4. Next to

PSK/EAP

, select either

PSK

EAP

5. Next to

Network Key

, enter a key. The key is entered as a passphrase

in ASCII format at both ends of the wireless connection. The

passphrase must be between 8-63 characters.

6. Click

Save.Settings

at the top of the window to save your settings.

If you are configuring the access point with a wireless adapter, you

will lose connectivity until you enable WPA-PSK on your adapter

and enter the same passphrase as you did on the access point.

Содержание DAP-1533




































































































Результаты поиска

Содержание DAP-1533

Отзывы:

Бренды по названию

Популярные бренды

D-Link DAP-1533, Руководство пользователя

Результаты поиска

Содержание DAP-1533

Отзывы:

Бренды по названию

Популярные бренды