manualshive.com logo in svg

Cypress S29CD016J, Руководство пользователя

Cypress S29CD016J - устройство памяти семейства 29CD с емкостью 16 Мбит. Для настройки и использования рекомендуется скачать бесплатное руководство по эксплуатации на сайте manualshive.com. Подробная информация о данном устройстве доступна для скачивания в разделе "Manual" на нашем сайте.

Поделиться
Скачать
background image

Document Number: 002-00948 Rev. *C 

Revised November 08, 2017

Page 74 of 74

© Cypress Semiconductor Corporation, 2005-2017. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress").  This document,
including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide.  Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other
intellectual property rights.  If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress
hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to
modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users
(either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as
provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products.  Any other use, reproduction, modification, translation, or compilation
of the Software is prohibited.

TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document.  Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes.  It is
the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product.  Cypress products
are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or
systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the
device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably
expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim,
damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other
liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.

Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.

S29CD032J
S29CD016J

S29CL032J

Sales, Solutions, and Legal Information

Worldwide Sales and Design Support

Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office 

closest to you, visit us at 

Cypress Locations

.

Products

ARM

®

 Cortex

®

 Microcontrollers

cypress.com/arm

Automotive

cypress.com/automotive

Clocks & Buffers

cypress.com/clocks

Interface

cypress.com/interface

Internet of Things

cypress.com/iot

Memory

cypress.com/memory

Microcontrollers

cypress.com/mcu

PSoC

cypress.com/psoc

Power Management ICs

cypress.com/pmic

Touch Sensing

cypress.com/touch

USB Controllers

cypress.com/usb

Wireless Connectivity

cypress.com/wireless

PSoC

®

 Solutions

PSoC 1 

| 

PSoC 3 

| 

PSoC 4

 |

 PSoC 5LP 

| 

PSoC 6

Cypress Developer Community

Forums

 | 

WICED IOT Forums 

| 

Projects

 | 

Video

 | 

Blogs

 | 

Training

 | 

Components

Technical Support

cypress.com/support

Содержание S29CD016J











































































Отзывы:

Нет отзывов

Похожие инструкции для S29CD016J

LaCie Hard Disk MAX Quadra Datasheet preview
Hard Disk MAX Quadra
Бренд: LaCie Страницы: 2
LaCie 8BIG RACK THUNDERBOLT 2 Quick Start Manual preview
8BIG RACK THUNDERBOLT 2
Бренд: LaCie Страницы: 28
Park Tool BX-1 Manual preview
BX-1
Бренд: Park Tool Страницы: 2
Hanover 9820010 Owner'S Manual preview
9820010
Бренд: Hanover Страницы: 21
Hamlet HXDU2RFID User Manual preview
HXDU2RFID
Бренд: Hamlet Страницы: 10
G-Technology G-SPEED FC Product Manual preview
G-SPEED FC
Бренд: G-Technology Страницы: 17
Naterial OCEAN SIDE 8435059720210 User Manual preview
OCEAN SIDE 8435059720210
Бренд: Naterial Страницы: 28
QNAP TS 73A Series User Manual preview
TS 73A Series
Бренд: QNAP Страницы: 68
SanDisk 80-11-00893 Brochure preview
80-11-00893
Бренд: SanDisk Страницы: 2
IBM TotalStorage NAS 100 Rack Installation Instructions preview
TotalStorage NAS 100
Бренд: IBM Страницы: 18
Suncast Brilliant by Design Deck Box DB7000 Owner'S Manual preview
Brilliant by Design Deck Box DB7000
Бренд: Suncast Страницы: 12
Seagate Barracuda 36ES2 ST318418N Installation Manual preview
Barracuda 36ES2 ST318418N
Бренд: Seagate Страницы: 2
Siemens SENSORPROM Instructions preview
SENSORPROM
Бренд: Siemens Страницы: 2
Siemens SISTORE AX Installation Instructions Manual preview
SISTORE AX
Бренд: Siemens Страницы: 40
Siemens Gigaset USB Stick 108 Manual preview
Gigaset USB Stick 108
Бренд: Siemens Страницы: 58
Siemens SIMODRIVE 611-D Installation Instructions Manual preview
SIMODRIVE 611-D
Бренд: Siemens Страницы: 1154
WOOD feeling 72113 Building Instructions preview
72113
Бренд: WOOD feeling Страницы: 27
Cavalry Hurricane ACBS3501000F Product Reference Card preview
Hurricane ACBS3501000F
Бренд: Cavalry Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды