Cypress PSoC CY8CTMG20 Series Скачать руководство пользователя страница 171 | Manualshive

Страница: 171 / 308

background image

PSoC CY8CTMG20x and CY8CTST200 TRM, Document No. 001-53603 Rev. *C

171

Full-Speed USB

20.3

Register Definitions

The following registers are related to Full-Speed USB in the PSoC device. For a complete table of the Full-Speed USB regis-
ters, refer to the Registers table

Summary Table of the System Resource Registers on page 106

. Register bits that are grayed

out in this document are reserved bits and are not detailed in the register descriptions that follow. Always write reserved bits
with a value of ‘0’.

20.3.1

USB_SOF0 Register

The USB Start of Frame Registers (USB_SOF0 and
USB_SOF1) provide access to the 11-bit SOF frame num-
ber. Start of frame packets are sent from the host (for exam-
ple, the PC) every 1 ms. For more information, see the

Universal Serial Bus Specification, revision 2.0

.

Bits 7 to 0: Frame Number.

The USB_SOF0 register has

the lower 8 bits [7:0] and the USB_SOF1 register has the
upper 3 bits [10:8] of the SOF frame number.

For additional information, refer to the

USB_SOF0 register

and the

USB_SOF1 register on page 194

20.3.2

USB_CR0 Register

The USB Control Register 0 (USB_CR0) is used to set the
PSoC’sUSB address and enable the USB system resource.

All bits in this register are reset to zero when a USB bus
reset interrupt occurs.

Note

Set the IMO frequency to 24 MHz and enable the 48

MHz clock in the OSC_CR2 register before USB is enabled.
See IMO_TR and CPU_SCR1 registers for selecting IMO
frequency as 24 MHz.

Bit 7: USB Enable.

This bit enables the PSoC device to

respond to USB traffic. ‘0’ is USB disabled. The device does
not respond to USB traffic. ‘1’ is USB enabled.

Bits 6 to 0: Device Address[6:0].

These bits specify the

USB device address to which the SIE responds. This
address must be set by firmware and is specified by the
USB host with a SET ADDRESS command during USB enu-
meration. This value must be programmed by firmware
when assigned during enumeration. It is not set automati-
cally by the hardware.

For additional information, refer to the

USB_CR0 register on

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

0,31h

Frame Number[7:0]

R : 00

0,32h

Frame Number[10:8]

R : 0

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

0,33h

USB Enable

Device Address[6:0]

RW : 00

«
...
169
170
171
172
173
...
»

Содержание PSoC CY8CTMG20 Series





















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PSoC CY8CTMG20 Series

Бренд: Wavetec Страницы: 17

Бренд: Calsense Страницы: 9

Smart Controller

Бренд: MaestroHome Страницы: 10

EtherNetIP ControlPlex CPC12EN

Бренд: E-T-A Страницы: 28

Бренд: Taie Страницы: 28

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: u-blox Страницы: 2

Бренд: vacuubrand Страницы: 12

Бренд: Vacon Страницы: 47

Бренд: Vacon Страницы: 40

Бренд: ZPA Pecky, a.s. Страницы: 36

Бренд: Fuji Electric Страницы: 12

Бренд: Rain Bird Страницы: 18

Бренд: Mitsubishi Страницы: 30

Бренд: Rabbit Страницы: 12

PersonalWorkplace Pro Video

Бренд: G&D Страницы: 56

Бренд: Delta Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды