manualshive.com logo in svg

Cypress PSoC CY8C23533, Техническое справочное руководство

Cypress PSoC CY8C23533 - микроконтроллер с широкими возможностями программирования. Получите бесплатно Техническое Руководство по управлению, загрузите его с manualshive.com. Эта детальная инструкция поможет вам максимально использовать функциональность этого продукта для ваших проектов.

Поделиться
Скачать
background image

Document # 001-20559 Rev. *D

229

Analog Interface

18.4.4

DEC_CR0 Register 

The Decimator Control Register 0 (DEC_CR0) contains con-
trol bits to access hardware support for both the Incremental
ADC and the DELISG ADC.

Bits 5 to 4: IGEN[1:0].  

For incremental support, these bits

select which column comparator bit is gated by the output of
a digital block. The output of that digital block is typically a
PWM signal; the high time of which corresponds to the ADC
conversion period. This ensures that the comparator output
is only processed for the precise conversion time. The digital
block selected for the gating function is controlled by
ICLKS0 in this register, and ICLKS3, ICLKS2 and ICLKS1
bits in the DEC_CR1 register.

Bit 3: ICLKS0.  

In conjunction with ICLKS1, ICLKS2, and

ICLKS3 in the DEC_CR1 register, these bits select up to
one of 16 digital blocks (depending on the PSoC device
resources) to provide the gating signal for an incremental
ADC conversion.

Bits 2 and 1: DCOL[1:0].  

The DELSIG ADC uses the

hardware decimator to do a portion of the post processing
computation on the comparator signal. DCOL[1:0] selects
the column source for the decimator data (comparator bit)
and clock input (PHI clocks). 

Bit 0: DCLKS0.  

The decimator requires a timer signal to

sample the current decimator value to an output register that
may subsequently be read by the CPU. This timer period is
set to be a function of the DELSIG conversion time and may
be selected from up to one of eight digital blocks (depending
on the PSoC device resources) with DCLKS0 in this register
and DCLKS3, DCLKS2, and DCLKS1 in the DEC_CR1 reg-
ister. 

For additional information, refer to the 

DEC_CR0 register on

page 110

.

18.4.5

DEC_CR1 Register 

The Decimator Control Register 1 (DEC_CR1) is used to
configure the decimator prior to using it.

Bit 7: ECNT.  

The ECNT bit is a mode bit that controls the

operation of the decimator hardware block. By default, the
decimator is set to a double integrate function, for use in
hardware DELSIG processing. When the ECNT bit is set,
the decimator block converts to a single integrate function.
This gives the equivalent of a 16-bit counter suitable for use
in hardware support for an Incremental ADC function.

The DEC_CR1 register’s bit 7 (ECNT) is only available in
PSoC devices with a type 1 decimator and is reserved in
PSoC devices with a type 2 decimator. 

Bit 6: IDEC.  

Any function using the decimator requires a

digital block timer to sample the current decimator value.
Normally, the positive edge of this signal causes the decima-
tor output to be sampled. However, when the IDEC bit is set,
the negative edge of the selected digital block input causes
the decimator value to be sampled.

Bits 5 to 0: ICLKSx and DCLKSx.  

The ICLKS3, ICLKS2,

ICLKS1, DCLKS3, DCLKS2, and DCLKS1 bits in this regis-
ter select the digital block sources for Incremental and DEL-
SIGN ADC hardware support (see the DEC_CR0 register). 

For additional information, refer to the 

DEC_CR1 register on

page 111

.

Add.

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

0,E6h

DEC_CR0

IGEN[1:0]

ICLKS0

DCOL[1:0]

DCLKS0

RW : 00

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

0,E7h

DEC_CR1

ECNT

IDEC

ICLKS3

ICLKS2

ICLKS1

DCLKS3

DCLKS2

DCLKS1

RW : 00

Содержание PSoC CY8C23533



























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PSoC CY8C23533

GATEWORKS Venice GW7300 Operating Manual preview
Venice GW7300
Бренд: GATEWORKS Страницы: 34
ICP Electronics ROCKY-P218BXA Pentium II & Creative Sound User Manual preview
ROCKY-P218BXA Pentium II & Creative Sound
Бренд: ICP Electronics Страницы: 39
ZiLOG Wireless Zdots Quick Start Manual preview
Wireless Zdots
Бренд: ZiLOG Страницы: 19
SOYO 5XB5 User'S Manual & Technical Reference preview
5XB5
Бренд: SOYO Страницы: 47

Бренды по названию

Популярные бренды

Загрузить еще бренды